Post by: Laverdaroo on April 09, 2024, 12:16:43 AM
It’s for Mejima, the 550, summers coming on and I’ve finally ‘got round to it’ so carbs on the bench and tuning imminent.
I’m struggling to get any this side of the Atlantic and deffo not a set of 4 of each. Stupidly I forgot to get them whilst over in the states last time I was there………..like you do!
Thanks all.
Sent from my iPhone using Tapatalk
Post by: Laverdaroo on April 09, 2024, 03:21:39 PM
They seem to be as rare as unicorn plop but still hoping.
Thanks all
Sent from my iPhone using Tapatalk
Post by: K2-K6 on April 09, 2024, 06:30:12 PM
https://www.primetools.co.uk/product/stahlwille-11085-jet-reamers/
Reaming is really accurate to finish the bore in brass.
Post by: Bryanj on April 09, 2024, 09:43:24 PM
Post by: Laverdaroo on April 09, 2024, 09:51:23 PM
If you have mate that would be bloody fantastic
If they were cheap to start with Nige, I’d invest in a set of reamer’s but for the possible 4 I MIGHT have to do is a bit of an investment I don’t need at the min. Good shout though, hadn’t even considered it tbh.
Sent from my iPhone using Tapatalk
Post by: Moorey on April 09, 2024, 10:20:16 PM
Is this the part # you are looking for. 99202-601-1000
Post by: Laverda Dave on April 09, 2024, 10:26:14 PM
Post by: Laverdaroo on April 10, 2024, 01:11:42 PM
Yeah, that’s them but struggling to find #100’s for some reason.
Is this the part # you are looking for. 99202-601-1000
Dave, although another tool in the tool chest is all sooper dooper and that, it’s cost prohibitive for me mate on what I need to achieve so as much as I want them being as much of a magpie as I ever was, I’ll keep chasing the jets for now, Bryan said he may have some kicking about so fingers crossed n all that.
Thanks for all the input fella’s appreciate it
Sent from my iPhone using Tapatalk
Post by: K2-K6 on April 10, 2024, 01:36:08 PM
They could likely and easily manufacture a set to spec too from simple brass stock in a small collet lathe. They're often making bushes (very similar in size) to repair old clock plates that have worn spindle holes. All reamed to accurate size in matching the tight tolerance needed.
Set of four aren't really much work in total labour time.
Could be an avenue to explore, perhaps if someone else needed some decent quality too.
Post by: Laverdaroo on April 10, 2024, 01:39:03 PM
Sent from my iPhone using Tapatalk
Post by: K2-K6 on April 10, 2024, 05:12:56 PM
Certainly worth talking it through with him, may be able to help out.
Post by: Bryanj on April 10, 2024, 07:41:46 PM
Post by: Moorey on April 10, 2024, 07:47:40 PM
Yeah, that’s them but struggling to find #100’s for some reason.
Is this the part # you are looking for. 99202-601-1000
Dave, although another tool in the tool chest is all sooper dooper and that, it’s cost prohibitive for me mate on what I need to achieve so as much as I want them being as much of a magpie as I ever was, I’ll keep chasing the jets for now, Bryan said he may have some kicking about so fingers crossed n all that.
Thanks for all the input fella’s appreciate it
Sent from my iPhone using Tapatalk
A bit of a long shot but they were used in Honda mowers. Could be worth a call as mowers are taken in every spring for a service because they won't start.
Post by: ozzybud on April 10, 2024, 09:22:17 PM
https://www.ebay.com/itm/266665109027?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=KS4RUr-YRBW&sssrc=4429486&ssuid=t3TSanHgRTi&var=&widget_ver=artemis&media=COPY