Recent Posts

Pages: [1] 2 3 ... 10
1
Tried it once, buggered up my old dumfone so never again
2
CB350/400 / Re: My New Project arrives after a 44 year wait!
« Last post by Laverda Dave on Today at 04:59:20 PM »
Peter Horton refurbished the original clocks including converting the rev counter to a suitable 400/4 item from the 250 rev counter that was on the bike. They look fantastic and I asked Peter to put the MPH/KPH face on the speedo for no other reason than I like them :-).

This morning I collected the finished paint set from Tony at Cyclesprays in Horsham, Sussex. He has done a marvelous job considering the tank I took to him! He placed the decals on the tank (decals supplied by Piki (Reddice) on here) and clear coated them with the same on the side panels. I'll decide it I want to put the saving lives sticker above the fuel tank, I don't really like the look of it!

I went to refit the carbs yesterday but thought I'd bench test them first with fuel to check the floats, of course one leaked really badly (No 1). A frustrating three hours spent adjusting the float and re-testing got me nowhere and it looks like I'll have to fit one of the new Keyster float valves to replace the original as the tip looks worn. What is it about 400/4 carbs, they work fine one minute and flood the next!

Next job will be to fit the carbs and handlebars with the switches.
3
CB350/400 / Re: My New Project arrives after a 44 year wait!
« Last post by Laverda Dave on Today at 04:52:00 PM »
A bit of progress over the past couple of weeks.

The big win was getting the engine finished and installed into the frame although I seriously can't recommend lifting an engine on your own from the work bench and onto the floor!

The rebore was done by Graham (Trigger) with the +50 NOS Honda piston sets. Graham also refurbished the head and this included replacing a bent inlet valve and a couplke of exhaust valves as well as a bit of welding to the combustion chamber where it had a chip on the edge.

Once the engine was in I installed the sump, put the forks in and the wheels on a temporary basis to allow me to get the rolling chassis onto the bike lift.

4
Ahhhh, thank you. It’s not hard for me to be baffled, much appreciated.

Not sure if anyone really uses tapatalk but I’m usually on my phone so it’s my usual way to access, any idea if there’s a way to see them using that?
5
Out & About / Re: OUT AND ABOUT 2024
« Last post by K2-K6 on Today at 03:51:03 PM »
Good luck with the op Dennis. I had a biopsy carried out on my right ear a couple of weeks ago and it is still too painful to even attempt to put a crash helmet on! Carpel tunnel issues, you must have been a MGP or Superbike racer, a true motorcycling god  ;)

Hope the result is a negative on biopsy Dave. I had similar about 8 yrs ago on right ear about 10 o'clock position, with no further action.

Nice bit of blanket stitch though  :) and all healed invisibly now.
6
Out & About / Re: OUT AND ABOUT 2024
« Last post by Laverda Dave on Today at 03:15:36 PM »
That looks fantastic in the sunshine.
I've not been out at all, once my ear gets better and I can put a crash hat on I'll be out in time for rfd sunshine 🌞
7
Out & About / Re: OUT AND ABOUT 2024
« Last post by Johnny4428 on Today at 03:10:52 PM »
Nice one! Looks as if you’ve got some nice weather too! Haven’t had my 750 started yet this year but first chance I get I will get it out of storage fit battery and give it a good check over and out and give it a good warm up!😜
8
If you go to Messages, there’s an Inbox and an Outbox.


Sent from my iPhone using Tapatalk
9
What’s the answer, I can’t see mine either, only received messages?
10
Out & About / Re: OUT AND ABOUT 2024
« Last post by Craizeehair on Today at 02:07:50 PM »
Had 20 miles on the 750 today, it’s the first run since winterisation and it felt great. I’ve been slow getting out this year as I’ve had a new shed build with a little project inside it and the other bikes haven’t been able to get out due to some garden work. They’ve spent most of the time living in the house. Normality has been resumed.
Pages: [1] 2 3 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal