This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - eem46
31
« on: June 21, 2018, 07:23:32 AM »
Ok thank! Which torque should I use? Add blue Loc-tite?
Kind regards,
Emiel
32
« on: June 20, 2018, 03:18:21 PM »
True, yellow is not easy, CMSNL has them, but I just bought them in France from ebay.
Do you advise to renew the expensive conrod bolts (stretch bolts) of just re use them on my stock bike?
Or go for the new cheaper version (stiffer) bolt 13213-KVO-000?
I searched the forum for a answer on the bolts, but people say yes or no.
33
« on: June 20, 2018, 07:30:44 AM »
Thanks!
Kind regards,
Emiel
34
« on: June 19, 2018, 12:43:17 PM »
Dear All,
Just started on my second HondaCb400Four engine, still learing about the crank and rods color codes.
Please let me know if I have it correct! :-)
Crankcase: B A B A A
Crank: A1 A1 A1 A1 2
Conrods: 2 2 3 2
Crankcodes are: B1 A1 B1 A1 A2 which translate into Green, Yellow, Green, Yellow and Green?
Conrod codes: A2 A2 A3 A2, which translate into, Yellow, Yellow, Brown or Green?? and Yellow
Please confirm A3 conrod code, Brown or Green?
Thank you!
Kind regards,
Emiel
35
« on: June 11, 2018, 06:57:59 AM »
Hi, maybe a very nice Aftermarket Stainless steel version from Kevin (TTR400).
Kind regards,
Emiel
36
« on: June 11, 2018, 06:54:28 AM »
Hi Menno,
I will contact you this week by mail.
Kind regards,
Emiel
37
« on: June 08, 2018, 07:46:52 AM »
Sidepanels were smooth on the outside, they are the black aftermarket versions like David Silver has, but even so, when they are rough you need to put filler/primer on and sand it! Like all paint work, the quality is set by the pre-work...
38
« on: June 07, 2018, 11:48:23 AM »
Hi Julie, which kind of clear coat? 2K? UV filter? Does it stick to polished alu, which is brushed afterwards?
Kind regards,
Emiel
39
« on: June 07, 2018, 08:53:07 AM »
Here the two layer sticker Menno made himself, again he fixed it. But I prefer a printed one layer sticker, of course the aftermarkets versions can be bad quality and than the clear coat can run behind the edges.
40
« on: June 07, 2018, 07:58:56 AM »
Hi Green1, I bought new black side cover for my Honda CB400F, I didnt mean he didn't painted the back side, I said he didn't sand and painted the sides nicely, he cut corners.
I hope my pic gets posted. Of course you don't finish the underside of the tank like the top side, but at least some color/paint to seal the white primer and with a ruby red tank and a bright white inside looks strange.
I am surprised that Menno use now Piki decals, one layer. I will contact him to redo my tank again (third time).
Kind regards,
Emiel
41
« on: June 05, 2018, 01:53:25 PM »
Hi, has anyone ever painted a Honda CB 400 Four tank with Menno? Results? I did one set of a Honda CB 400 Four side covers plus tank, but was not happy with the result. The selfmade tank stickers by Menno (two layers) were not fully covered by clear coat, so there was a white reaction around them. He doesnt paint/seal the under side of the tank against corrosion. Side covers were not sanded on the side (frame tube side). I sent tank back for repair stickers and spraying underside, he never sanded or cleaned the underside, he just put a shot of paint on it and my clear coat now has metallic floks in it. Yes he offered to fix it again, but my patience was over. Maybe he is better with non CB400F tank with no stickers. But yeh I seen better painters..
42
« on: May 14, 2018, 10:53:18 AM »
Hi,
Has anyone mounted the needle bearing version? It has no seals at all, and the two side bearings cant be greased that easy. Kind regards, Emiel
43
« on: May 03, 2018, 09:45:25 AM »
Ok, didnt know that! Just google the OEM number, maybe it pops up on ebay. Or try https://www.cmsnl.com/
45
« on: May 01, 2018, 12:20:09 PM »
|
Show Posts