This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - davefirestorm
Pages: 1 2 3 [4] 5 6 ... 20
46
« on: March 03, 2021, 11:08:54 PM »
My thoughts too regarding weather,fingers crossed then 😁🤞🏽
47
« on: February 12, 2021, 10:07:40 PM »
Wouldn’t take it as a gift,rather stick a motor on my shed at least no fu##er would be able to see me going down the road.You can’t polish a turd but they’re trying to sell one
48
« on: February 05, 2021, 07:20:31 PM »
I have a Delkevic 4-1 stainless system on my F0 if your not after the original look it fits ok runs fine and not too noisy with baffles in.Bought mine with intention of rechroming original but haven’t got round to it yet😁
49
« on: January 30, 2021, 09:26:22 PM »
One of the nicest looking BSAs built I reckon.A friend of mine built a replica for his son few years ago.Eddie Dow had a Renault car dealership in Banbury with a RGS in the showroom in early 80s I didn’t know who he was then and not sure if I met him 😁
50
« on: January 18, 2021, 07:45:57 PM »
I once superglued my thumb and 2 fingers to my cars roof rack 😂😂
51
« on: December 13, 2020, 10:50:06 PM »
My sentiments too,it’s your bike put whatever you like on it
52
« on: December 13, 2020, 08:51:13 PM »
Personally wouldn’t put a black/silver plate on a post ‘73 bike and in the day 1970 onwards one would put a reflective plate on their bikes
53
« on: December 01, 2020, 04:45:32 PM »
My Harley was this this colour till recently 😂😂
[ Guests cannot view attachments ]
54
« on: October 02, 2020, 08:05:23 PM »
I worked processing titanium rotor blades for jet engines many years ago and a Kolene salt bath would strip the tungsten coating from the blades leaving the titanium like new
55
« on: October 02, 2020, 06:42:21 PM »
Trichloroethylene been banned for a while now,can be deadly inhaling the fumes believe it was used in dry cleaning? and industrial uses too.I had a bottle of Trich on shelf in garage got knocked over and dripped onto me cd/radio melting the casing.There is a safer substitute available but strangely smells same
56
« on: September 30, 2020, 09:05:26 PM »
In a previous life I machined parts to recondition Challenger tank hydraulic steering units and would sleeve worn bearing surfaces by shrinking a sleeve in using araldite to bond it.I’d still pin a brake hub sleeve😁
57
« on: August 27, 2020, 02:46:48 PM »
Bargain  Will look out tomorrow.Often pick up the odd bargain in the Supermarkets I bagged 4 cans of WD40 1/2 price few weeks back
58
« on: August 19, 2020, 09:31:52 PM »
76mm flexi hone from Amazon for £30 they last for years
59
« on: August 19, 2020, 08:04:15 PM »
You could go quite a bit bigger as you can shove them up a much smaller hole but obviously more force needed and powerful drill,when I used one I held the single cylinder in lathe chuck and the flex-hone in a Jacobs chuck
60
« on: August 19, 2020, 07:01:36 PM »
I’ve used one of these on cylinders in the past ( Old Brit bikes ) easy to use in an electric drill giving nice overlapping x hatch pattern
[ Guests cannot view attachments ]
Pages: 1 2 3 [4] 5 6 ... 20
|
Show Posts