Recent Posts

Pages: 1 [2] 3 4 ... 10
11
CB350/400 / Re: CB400F2 speedometer face plate
« Last post by Mikep328 on May 20, 2024, 10:40:02 PM »
My 1976 UK CB400 has only miles.
12
CB350/400 / CB400F2 speedometer face plate
« Last post by Athame57 on May 20, 2024, 10:26:24 PM »
Does the UK CB400F2 have a speedometer have both MPH and KPH on it?
13
The Black Bomber Board / Re: 67` Bomber running problems
« Last post by mo goldie on May 20, 2024, 10:22:34 PM »
You have lost me with that one ?

tried them in DSS and all discontinued
 
14
The Black Bomber Board / Re: 67` Bomber running problems
« Last post by Bryanj on May 20, 2024, 10:13:57 PM »
Part number is 41201283000 so i would say 283 not 280 but that is a pure guess
15
Project Board / Re: Mike's CB550 Project
« Last post by McCabe-Thiele (Ted) on May 20, 2024, 09:55:46 PM »
My BiL removed mine using one of these on my 400 it removes the bottom race without causing any damage .
Ideal if you fit a new bottom race and then need to remove it to fit a shim underneath.
I bought one for myself as it was not expensive when I was fitting a taper roller kit to my 500. https://www.ebay.co.uk/itm/403899872756


Alternatively as you described plus heat might help.

.
16
Project Board / Re: Mike's CB550 Project
« Last post by Mike_Berkshire on May 20, 2024, 09:12:12 PM »
Whilst I’m working on the forks I’m thinking ahead; optimistically, about putting the front end back together again. I’m going to stick with old school bearings following the comments. I’m assuming I need to remove the lower bearing cup/ race from the the stem on the lower triple tree as it will be worn. Looking at it there is a rubber washer (maybe 2?) beneath it and a shim beneath that. I guess these are removed by levering/bashing from beneath using a drift or cold chisel and then the new one needs a new shim and rubber washer(s). Does this sound like the right approach?
17
CB750 / Re: CB750 sohc F2
« Last post by archmill on May 20, 2024, 08:46:30 PM »
[ Guests cannot view attachments ] no arrows guys but the pistons have an indented circle on them. Assume this is front ?
18
The Black Bomber Board / Re: 67` Bomber running problems
« Last post by mo goldie on May 20, 2024, 08:15:01 PM »
Well he is just a bloke on Ebay Ash so don`t know how good he is..........as he just asked to supply the dimensions so he could check to see if they is one to match it ..... so if you can just tell me if it is flat on both sides will due I think.   
19
CB750 / 750K0 Disc /Hub info for JoJoTut
« Last post by AshimotoK0 on May 20, 2024, 08:12:41 PM »
Went to Steve's tonight to check his UK CB750K0 stuff / look at his chromed carbs !!

This is the hub info you need Steve  ... Great to meet you !!

[ Guests cannot view attachments ] [ Guests cannot view attachments ]
20
The Black Bomber Board / Re: 67` Bomber running problems
« Last post by AshimotoK0 on May 20, 2024, 08:08:58 PM »
Quote from: mo goldie on May 20, 2024, 08:06:46 PM
Hi Ash

This is what he sent back so if you Know what he is on about can you have anther look at the sprocket please to give him the more info.

Hi, You have not said what chain pitch you have but I assume it is 530. The 4 mounting bolt holes distance apart (known as the p.c.d.) is taken from the centres of the bolt holes.
I make it 74mm centre hole as there is nothing listed with 73.7mm. The p.c.d. at 110mm with 10mm bolt holes.

Is the sprocket flat on both sides or a recessed ring on the inner face? I think it might be 280 sprocket type but I now need to check to see if this is still available.

May be simpler if I donate my used one to you to give him. Just pay postage.
Pages: 1 [2] 3 4 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal