This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Johnwebley
Pages: 1 2 [3] 4 5 ... 211
31
« on: March 26, 2024, 11:38:07 AM »
Next time you're in a newsagents
Check the small ads in Motorcycle sports and leisure
Some nice looking older Hondas
Sent from my SM-A546E using Tapatalk
32
« on: March 26, 2024, 11:31:49 AM »
Didn't realise you were running non standard pods and exhaust
As others will comment, short pods don't work well,
The intake length is designed to work with a plenum chamber/airbox
It's to do with the pulses of the airstream
Good luck
Sent from my SM-A546E using Tapatalk
33
« on: March 26, 2024, 10:23:46 AM »
NRP carbs
Those are a big increase on standard for the mains
Sent from my SM-A546E using Tapatalk
34
« on: March 25, 2024, 07:13:37 PM »
I seem to remember the inner was two lengths
Standard about 20mm
Short about 13mm
The shorter were for high speed,
The centre being less likely to lift at high speed,
Sent from my SM-A546E using Tapatalk
35
« on: March 22, 2024, 01:39:11 PM »
Yes,
I fitted a solid state unit,
About 8 years ago
Seems to work perfectly
Sent from my SM-A546E using Tapatalk
36
« on: March 20, 2024, 01:08:58 PM »
Just trying to replace the alloy washers at the camshaft ends I am trying Dowty seals Same size,thickness Should be an acceptable substitute  Sent from my SM-A546E using Tapatalk
37
« on: March 20, 2024, 01:04:11 PM »
Only the pivot hole,
I took 0.5mm from both sides of the shoes
Sent from my SM-A546E using Tapatalk
38
« on: March 20, 2024, 12:05:46 PM »
I found after market shoes are to wide at the pivot end,
I normally use a file to remove some alloy so the double washer and split pins fit,
Just care needed to get the shoes to fit square
Sent from my SM-A546E using Tapatalk
39
« on: March 18, 2024, 04:13:59 PM »
And a Slippery Sam replica?
Sam Sunderland is a hero, to win Dakar is amazing
Sent from my SM-A546E using Tapatalk
40
« on: March 18, 2024, 03:15:11 PM »
First decent day for ages Really enjoyable  Sent from my SM-A546E using Tapatalk
41
« on: March 16, 2024, 07:42:12 PM »
Very nice
Sent from my SM-A546E using Tapatalk
42
« on: March 16, 2024, 06:37:37 PM »
43
« on: March 16, 2024, 06:07:54 PM »
A Dremel type tool is probably something I should have bought over a thirty tears ago when I was doing all my home DIY.
For how much I would use one today I can't justify the outlay - a recommended cheapo might be an option.
I think mine costs about £12 with assorted tools, Sent from my SM-A546E using Tapatalk
44
« on: March 16, 2024, 04:33:52 PM »
I bought a rechargeable Chinese copy of dremel from Aliexpress,
Complete with tools,
Works great, for the amount I use it, can't fault it,
Sent from my SM-A546E using Tapatalk
45
« on: March 16, 2024, 03:09:40 PM »
Oil, it should be lubed by the oil in the engine,
I use a HMP grease on the worm drive, because it gets very hot,
Also make sure the cable is smooth, some you can oil, some you can't
Sent from my SM-A546E using Tapatalk
Pages: 1 2 [3] 4 5 ... 211
|
Show Posts