Recent Posts

Pages: 1 [2] 3 4 ... 10
11
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by mickwinf on May 19, 2024, 10:18:23 PM »
I did have a bid but not successful.
12
CB350/400 / Re: Brake Torque Arm colour
« Last post by Athame57 on May 19, 2024, 10:16:29 PM »
Just took a look at the part on CMSL ( why you not do this before I hear someone say  ;D ) It seems they start out as BZP, I can see myself stripping the paint and polishing things up, and then finding out why they end up being painted?  :-\
13
CB350/400 / Re: Brake Torque Arm colour
« Last post by Athame57 on May 19, 2024, 10:04:32 PM »
Quote from: Nurse Julie on May 19, 2024, 08:32:16 PM
I'm sure it could be black or BZP, the same as the 500/550. And, it's F I remember correctly, both finishes are the same part number 🤔🤔🤔
These are the two colours I keep seeing Julie! I'm not becoming a fanatic over it, but I'm keen all the same to bring my bike close to original as I go along. Pattern parts are usually ok with me though.  ;)
14
Project Board / Re: Doms CB550F1 project
« Last post by Bryanj on May 19, 2024, 09:49:04 PM »
Just got to work and was going to suggest standard bars might help
15
The Black Bomber Board / Re: 67` Bomber running problems
« Last post by AshimotoK0 on May 19, 2024, 08:58:58 PM »
Quote from: mo goldie on May 19, 2024, 07:19:03 PM
are thanks Ash........ well its Not just the mrs then that I upset LOL

so I have sent that off to the bloke .... I hope he will find a sprocket that will fit with them Dimensions.

so thanks Again Ash to the rescue  ;D or should I say MR Honda  ;D

Well it went OK 'cos I found a NOS one in there for my own Bomber I wasn't aware I had  and didn't realise they are so rare !
16
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by AshimotoK0 on May 19, 2024, 08:55:24 PM »
Near to me (across the field from my house) but I have enough junk ... so deffo not me.
17
CB350/400 / Re: Brake Torque Arm colour
« Last post by Nurse Julie on May 19, 2024, 08:32:16 PM »
I'm sure it could be black or BZP, the same as the 500/550. And, it's F I remember correctly, both finishes are the same part number 🤔🤔🤔
18
CB350/400 / Brake Torque Arm colour
« Last post by Athame57 on May 19, 2024, 08:26:55 PM »
I'm beginning to notice the brake torque arm on the CB400F/2 in different colours in different pictures, how should the standard one be?
19
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by Bryanj on May 19, 2024, 07:28:22 PM »
That was a good haul, too much and too far away for me, at least 3 of the rear brake pedal retun spring in there
20
Project Board / Re: Doms CB550F1 project
« Last post by DomP on May 19, 2024, 07:25:28 PM »
I got there in the end, it took ages to get air out of the new master cylinder which was made harder because my clip ons have a 15° downward angle on them so air was sitting at the top slightly above the mc piston inlet.  Solved it by rolling the bike up the slope of my drive and putting it on the side stand. 

Lesson learned!
Pages: 1 [2] 3 4 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal