This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Oddjob
Pages: 1 ... 212 213 [214] 215 216 ... 287
3196
« on: September 01, 2022, 11:50:42 PM »
Sorry Mick, got Nigel on the brain. Was just replying to his PM and forgot who I was speaking to.
Shims are in a small bag. I'll find a box for the cover as soon as I make sure it's ok, I have at least 6 of them so I'll find a good one.
3197
« on: September 01, 2022, 11:48:57 PM »
Oh good it's Mick who'd going senile.
All done, all 10 envelopes done, 8 posted tomorrow and 2 already in the post.
I'll let you know when I check my bank account Nigel, I don't check it everyday but it doesn't matter, yours is in the post.
3198
« on: September 01, 2022, 06:19:42 PM »
DOH, yep course he is, going senile I think.
3199
« on: September 01, 2022, 06:19:13 PM »
Got quite a few Nigel, no cost to you except postage.
3200
« on: September 01, 2022, 06:17:26 PM »
I'll see if I can find a needle roller out of a 500 for you Gary. No cost. Do you have any of the pins out of one?
It was the slot cut out of the casing where that needle bearing goes, can't remember it on the 500, probably just old age setting in.
3201
« on: September 01, 2022, 06:14:48 PM »
Sorry 3scs, got the payment but no PM with an address.
Sorry Phil, it's Nigel that's in Scunny, you are of course in upmarket York. My deepest apologies.
3202
« on: September 01, 2022, 01:18:15 PM »
If you're sending stuff up to me then yeah send it back so I can marry it back up with it's mate. If not then wait until you are, no rush. STOP bloody buying stuff like that collar, I must have one of them lying around somewhere, ask first before spending money, it's not a problem and I'd sooner all my little bits like that get used than thrown away when I kick the bucket 
3203
« on: September 01, 2022, 01:13:41 PM »
Looking at the pics I spotted the locating pin for the needle roller wasn't fitted for the countershaft, have they both been fitted now? Also make sure the needle bearings locate into them, sorry if that sounds patronising but better to do that than let you make a simple mistake.
The crankcase looks to be a 550 pair, yet you're using a 500 gearchange fork setup. Am I wrong?
The gearbox looks to be 550 or it's had a 550 needle roller fitted. The only way to know for sure is to start counting teeth on the gears, there are slight differences between the 500 and 550 gears.
3204
« on: September 01, 2022, 01:04:15 PM »
I have payments and addresses now for 7 sets and Nigel is organising something else. I have Bryan, Roo, Mick, Simon, John and already sent Phil from Scunny and Phil from Wigan. I think that leaves just 3scs.
For information only, Friends and Family is a selection you make just after you chose who you're sending money too and how much, address can be added in the notes for seller section on the last page IIRC, just before you press send.
They are now all sold, even my set was sold to a friend.
However if anyone else is desperate I can get some more, don't really want to but I'd sooner do that than let someone down.
3205
« on: August 31, 2022, 10:34:39 PM »
Got a payment from John Wood but no postal address. Please PM me with it so I can send you the shims.
3206
« on: August 31, 2022, 10:32:16 PM »
Whatever you do Ted don't put 2 emulsion tubes together as one atomises and the next splits that atom, the resultant explosion has to be seen to be believed 
3207
« on: August 31, 2022, 10:24:02 PM »
Ok, well they are all bagged up in sets.
Please make payment to PimlottKen@GMail.com and make sure you include your postal address please.
I'd appreciate it being sent Family And Friends if you can.
3208
« on: August 31, 2022, 03:45:56 PM »
I don't usually refer to non UK variants as I don't know for certain what each country got.
3209
« on: August 31, 2022, 12:49:08 PM »
Does the stop screw still have its little collar fitted?
3210
« on: August 31, 2022, 12:48:12 PM »
You get a free horn with it 
Pages: 1 ... 212 213 [214] 215 216 ... 287
|
Show Posts