1
CB350/400 / Re: speedo trip rewind knob
« on: June 30, 2022, 03:06:24 PM »
May be deep, But true. If you don't learn you keep making the same mistakes over and over ??
Try our new info resource - "Aladdin's Cave" (Main menu)
Just added a separate link to Ash's Dropbox thread (shortcut)
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to. 1
CB350/400 / Re: speedo trip rewind knob« on: June 30, 2022, 03:06:24 PM »
May be deep, But true. If you don't learn you keep making the same mistakes over and over ??
2
CB350/400 / Re: speedo trip rewind knob« on: June 30, 2022, 10:08:24 AM »
Wish i had known this before Never mind Its not a crime to make a mistake !! But its a crime not to learn from it ?? Ross
3
CB350/400 / Re: speedo trip rewind knob« on: June 29, 2022, 10:00:04 AM »
Cheers for that Matt. If Peter hasn't got any then i will take you up on your offer
Well Paul, you learn stuff everyday I never knew they unscrewed Only read that to remove the knob use a dremel to cut a slot in the knob which can be repaired This i was trying but totally destroyed the Knob Every day a school day That is now logged Thanks Ross 4
CB350/400 / Re: speedo trip rewind knob« on: June 28, 2022, 10:36:36 PM »
Peter has just messaged me He is away till the weekend but may have one
5
CB350/400 / Re: speedo trip rewind knob« on: June 28, 2022, 02:56:37 PM »
Was talking with him about faces etc and he suggested cb750faces for the parts Just assumed he didn't stock any But worth a message cheers
6
CB350/400 / speedo trip rewind knob« on: June 28, 2022, 01:51:08 PM »
Hi All
Does anyone have a speedo trip rewind knob for a cb400 that they are willing to part with It is a push fit on splines Unfortunately had to distroy mine while doing a refurb and they are not listed as a spare Thanks Ross 7
Misc / Open / Re: Looking for my next project - a 400/4 with a blown engine anywhere?« on: June 02, 2022, 12:52:23 PM »
Hi Ted I also asked questions Although I'm not interested They did reply to say it was UK registered So i asked for Reg No Engine No and Frame No so i could check the bikes history So far no reply Seems a bit suspect Personally I would want to see it in the flesh Better to walk away than get burnt
8
Recommended Sources for Parts and Services / Stainless steel fasteners« on: May 28, 2022, 09:22:03 AM »
HI All If anybody is looking for stainless fastners Please check out Kayfast in Wakefield They do both A2 & A4 at very good prices and are very quick to send Worth checking
Ross 9
CB350/400 / Re: Front fork strip down« on: May 07, 2022, 06:27:11 PM »
I understand the bodge, but there are no leaks, as can be seen in photo No old staining on the paper I just don't understand why do it in the first place when its not needed ??
10
CB350/400 / Front fork strip down« on: May 07, 2022, 05:35:01 PM »
Stripped. The forks for re-chrome Look what I found?… Kitchen roll packed in Not sure why as there were no leaks The paper was dry What are your thoughts??? Ross
11
CB350/400 / Re: Carb butterfly clips« on: March 15, 2022, 03:29:52 PM »
400fourbits has used ones if any good for you
12
Desperately Seeking!! / Re: CB72 CB77 Main stand Return spring or Dimensions ... available in UK« on: February 18, 2022, 09:44:38 AM »
Hi Ash My measurements are the wire thickness 3mm Diameter of spring 17mm Number of coils is 18 As the bike is on its stand i cannot accurately measure length If you want this measure let me know and i will take it off measure and send you a picture Ross
13
Desperately Seeking!! / Re: CB72 CB77 Main stand Return spring or Dimensions ... available in UK« on: February 17, 2022, 04:35:20 PM »
Hi Ash Just measured the spring on my CA77 I believe its the same part number The wire is 3mm and the outside diameter 17mm
Hope this helps Ross 14
Project Board / Re: Alloy tank« on: February 06, 2022, 02:41:04 PM »
Hi Ian Have a look at these Tab Classics and The tank shop Half price of what you've seen Ross
15
CB350/400 / Re: Chrome plating« on: January 15, 2022, 09:49:18 AM »
will check them out I did get a quote from Agbrigg in Leeds @ £120+vat + postage for my front mudguard Considering a new one
is £174 freepost hummm |