This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - B11sey
1
« on: April 23, 2023, 02:30:56 PM »
Sounds like a good plan 👍
2
« on: April 23, 2023, 11:17:45 AM »
Really useful info. We used the same method with copper to seal cooling circuits on mould tools but peened them really hard to create a seal. Hope I can get the aluminium to seal a bit easier 😅
3
« on: April 23, 2023, 10:08:23 AM »
Thanks @Sesman. I was hoping to do that but how easy is it to re-seal. Is the plug just pressed and peened or is there a seal in front of it?
4
« on: April 23, 2023, 08:07:47 AM »
Does anyone know how to remove/ replace the blank plugs at the ends of the camshaft oil feed channel on a 500 K0? I want to vapour blast but not confident about cleaning after unless I remove these plugs
5
« on: April 18, 2023, 11:08:12 AM »
I’m sure this has been covered before but does anyone know the correct colour to paint the engine cases. I’m thinking of creokote for the barrel and head and 2 pack for the crankcases.
6
« on: February 23, 2023, 07:43:50 AM »
Thanks Bryan,
I will admit it was a great machine to start from and we've had a particularly crap Winter when being in the workshop was a good option and very few interruptions. I even refurbished the clocks which I had thought would be next Winters job.
(Attachment Link)
Still have to fit the 069 carbs and airbox
(Attachment Link)
Looks like the clock bracket needs a bit of straightening and bar clamps re-finishing sometime.
Ian
I would be really interested in a details of your Speedo/tachometer repairs. Any chance of a picture of the crimping tool you made?
7
« on: February 07, 2023, 08:40:48 PM »
Thanks Ashimoto useful information
8
« on: February 07, 2023, 05:47:08 PM »
Ashimoto
My engine number shows it was made before the gearbox mods so I definatly need to check this
9
« on: February 07, 2023, 01:36:00 PM »
The K0 needle roller seizing on the mainshaft issue was significant though ... my bearing was well and truly fooked and Graham (Trigger) once showed me a very low mileage K0 countershaft that had been fried by the needle bearing seizing. It's a double-bunched roller type and on mine the alloy carrier cage had disintegrated.
I’ll check mine when I split the cases. Are there any proprietary fixes for the K0 gearbox issues?
10
« on: February 07, 2023, 11:49:31 AM »
I think the switch problem is greatly overstated. Ran my K0 for 9 yrs (commuting to work in the dark all winter) before layup and I didn’t even know there was a problem until read it on here
11
« on: February 06, 2023, 04:50:08 PM »
Had a reply from Honda UK which said the information has to come from Japan and may take up to 6 weeks. I guess this is their std system so waiting with fingers crossed
12
« on: February 04, 2023, 01:59:14 PM »
Done a load of rides all over europe including the eastern block before the Berlin wall came down and all the way to India on silly small bikes like one of my CD250's. Took a Piaggio typhoon 50cc from Newport pagnell to Thessaloniki on a 3 day trip 
[/quote
Now that’s a proper adventure ride
13
« on: February 04, 2023, 01:05:45 PM »
These trips seem a bit tame today with reliable adventure bikes, Satnav, more money and the security of a mobile phone signal but back in the day you needed a proper sense of adventure to travel far.
14
« on: February 03, 2023, 12:57:24 PM »
I have emailed Honda UK (nothing to lose) and will let you know the outcome
15
« on: February 02, 2023, 09:13:10 PM »
Hi Seabeowner
Longest trip was through France,Spain to Morocco along coast to Marrakesh then to the oasis Ouarzazate and back along edge of the desert to Fez. 2 up the CB handled it all without any problems apart from getting through the crowds that formed in the towns
|
Show Posts