This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - tworiversuk
1
« on: February 15, 2010, 05:40:05 PM »
Hi All,
does anyone know where I can get hold of stainless footrest springs for the front footrests on my CB750K7
THANKS FOR YOUR HELP
2
« on: May 01, 2009, 06:15:01 PM »
Hi All,
has anyone fitted a rear Givi/monokey rack to a cb750K7 , I ask this knowing they are not available for this model ,but knowing you enterprising people someone may have adapted one from another model.The side arms are the only part to adapt.I thought if I could find a pair straight and long enough, bolt them to the shocker top bolt and I could make a small plate to fit to the rear fender bolt and bob's your uncle.Anyone tried and sorted it ?
Mike
3
« on: January 25, 2009, 03:18:25 PM »
Hi guy
just a couple of shots after my ride to Instow in Devon
4
« on: December 08, 2008, 08:10:41 AM »
Hi Mick
all finished now pictures to follow
Mike
5
« on: December 08, 2008, 08:09:36 AM »
Hi Guys, got the keys from a guy in the states, where else!! 2 for $30 inc postage genuine Honda ones not re-cuts http://www.motorcyclekeys.com/keys.htmlthanks for the help Mike
6
« on: December 03, 2008, 02:45:36 PM »
Hi,
can anyone shed some light on the type of key my bike requires ,I have one key and need another blank to have cut, David Silvers says it's a type 'A' OR 'B' any idea's it has the groove on the right hand side and the number is 3 digits long no letters
mike
7
« on: November 03, 2008, 05:58:38 PM »
has anyone got 2 chrome rings for the speedo and tacho clocks, rebuilt mine and totally trashed the rings, ,used the pry off soloution should have used the cut and jb weld solution, will buy the whole clocks if I have too
Mike
8
« on: November 03, 2008, 05:57:44 PM »
Hi, well you can get a rim from silvers, I had my wheels rebuilt using a new rim from Silvers and s/steel spokes ,just because there is no problems with rust , the wheels was rebuilt by http://www.devonrimcompany.com/classicrims.htm# from devon
9
« on: October 26, 2008, 08:50:40 PM »
Mick,
you little beauty, just what I needed, thanks so much
Mike
10
« on: October 26, 2008, 06:14:01 PM »
Hi Guys,
Anyone got the lower front engine bolt, the log one that goes under and through the engine, lying around in there workshop Honda part number 90152300010, just stripped mine ,recut it smaller and stripped it again,if you have one contact me direct on, michael.t.baldwinATbtinternet.com, with a price inc postage to devon
cheers
Mike
Edited by SteveD: Changed the email address to keep the webbots at bay...
11
« on: October 23, 2008, 06:41:44 PM »
Hi Guys,
painted the engine with 2 coats of simmoniz VHT silver, looks the dogs boll**ks, spent the afternoon polishing the cases, tappet cover and altenator cover done so far, far easier when you shotblast with glass beads,one question which side does the earth strap go to ,the brake switch side or tuther?found a supplier for the push nuts that keep the seat chrome rail on, stainless as well,
12
« on: October 18, 2008, 09:38:46 AM »
well all stripped out and 4 days later the powder coating has arrived back, loverly job, any idea's as to the paint to use on the engine? and has anyone a seat trim for sale must be perfect no scratches
Mike
13
« on: October 02, 2008, 08:08:07 AM »
Hi boys and girls,
just started my resto of the CB750K7 I bought 6 months ago, when I figure out how to put pictures in my posts I will do so.I will I am sure need your help along the way, I have sent the carbs off to be stripped and vapour blasted and rebuilt with brand new internals,stripped all the oil tank and lines,left side electric panel and battery tray,seat ect off, tonight the engine will come out ( I hope ) made up my engine stand as seen on this site, ready for the paint job, so come alomg with me and see how I get on
Mike in Devon ( UK )
14
« on: August 04, 2008, 08:05:07 AM »
Hi ALL
has anyone got a K7 owners manual for sale? must be good nick also anyonw know where I can get the sticker from that fits on the chain guard to warn about the chain been a 'o' ring type and not to power wash it
mike
15
« on: July 23, 2008, 08:11:29 PM »
cheers just received it in the post
|
Show Posts