Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - simonc

Pages: 1 [2] 3
16
New Member Introductions / Re: 500 550
« on: April 18, 2020, 10:25:18 PM »
Cheers I have already stripped cleaned re jetted bigger set float heights. will decide later on final jetting new exhaust req
no real plan with this one. resprayed tank as a change from mechanical work, also restoring cb 72 super hawk so plenty to do ;)

17
New Member Introductions / Re: 500 550
« on: April 18, 2020, 07:39:32 PM »
thanks for that info much appreciated :)

18
New Member Introductions / Re: 500 550
« on: April 18, 2020, 07:21:15 PM »
cb500E2028001 engine ,cb550f 2105260 frame

19
New Member Introductions / Re: 500 550
« on: April 18, 2020, 07:08:51 PM »
yes i knew thank you is it ok to post engine and frame no on here?

20
New Member Introductions / Re: 500 550
« on: April 18, 2020, 07:02:43 PM »
sorry i bought it as is  lol ;D :D :D

21
New Member Introductions / Re: 500 550
« on: April 18, 2020, 06:55:24 PM »
yes i realise that it is not original  but it came that way all the plug ins  fit surely  this has been done before. I have just  looked at engine no ending 500E is the engine an f dont know year, excuse my ignorance.

22
New Member Introductions / Re: 500 550
« on: April 18, 2020, 06:36:02 PM »
us import came this way at the time i had 3 other cb 550fs but this was cheap? :D

23
New Member Introductions / Re: 500 550
« on: April 18, 2020, 06:31:41 PM »
Ah that may explain why it looked as though it had been hot wired. the replacement harness is the same as one fitted is there away round this everything on running gear, frame is cb 550f ?

24
CB500/550 / Re: 550 k3 harness
« on: April 18, 2020, 06:06:38 PM »
through frame

25
New Member Introductions / 500 550
« on: April 18, 2020, 05:57:14 PM »
Hi I am in the middle of re building a 550f2 ? 1977 usa import came with 500 k? engine fitted have removed engine stripped engine looks to be very good internally oa standard bore all in spec i have de glazed bores unbelievable condition.
wiring loom poor but have very good replacement,Is the wiring on 500 same as 550f? ::)

26
New Member Introductions / Re: New To The Forum
« on: April 18, 2020, 05:42:45 PM »
if? it is a bitsa it looks good why change it

27
Project Board / Re: Meet my new 550f2
« on: April 18, 2020, 05:00:59 PM »
correct silencer becoming rare item now[ rust out] good project

28
New Member Introductions / Re: Hello from sweden
« on: April 18, 2020, 04:40:38 PM »
nice looker ;)

29
Tricks & Tips / Re: Portable media blaster?
« on: April 18, 2020, 04:30:04 PM »
 I also use a soda blast gun on parts agree slow using a lot of media, but good   patience required and it does kill grass. ;)

30
Also dont know pd carbs so cannot comment on gaskets sorry. but clean clean clean/ check float heights/  :o

Pages: 1 [2] 3
SimplePortal 2.3.5 © 2008-2012, SimplePortal