This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Johnwebley
Pages: 1 ... 3 4 [5] 6 7 ... 213
61
« on: March 20, 2024, 01:04:11 PM »
Only the pivot hole,
I took 0.5mm from both sides of the shoes
Sent from my SM-A546E using Tapatalk
62
« on: March 20, 2024, 12:05:46 PM »
I found after market shoes are to wide at the pivot end,
I normally use a file to remove some alloy so the double washer and split pins fit,
Just care needed to get the shoes to fit square
Sent from my SM-A546E using Tapatalk
63
« on: March 18, 2024, 04:13:59 PM »
And a Slippery Sam replica?
Sam Sunderland is a hero, to win Dakar is amazing
Sent from my SM-A546E using Tapatalk
64
« on: March 18, 2024, 03:15:11 PM »
First decent day for ages Really enjoyable Sent from my SM-A546E using Tapatalk
65
« on: March 16, 2024, 07:42:12 PM »
Very nice
Sent from my SM-A546E using Tapatalk
66
« on: March 16, 2024, 06:37:37 PM »
67
« on: March 16, 2024, 06:07:54 PM »
A Dremel type tool is probably something I should have bought over a thirty tears ago when I was doing all my home DIY.
For how much I would use one today I can't justify the outlay - a recommended cheapo might be an option.
I think mine costs about £12 with assorted tools, Sent from my SM-A546E using Tapatalk
68
« on: March 16, 2024, 04:33:52 PM »
I bought a rechargeable Chinese copy of dremel from Aliexpress,
Complete with tools,
Works great, for the amount I use it, can't fault it,
Sent from my SM-A546E using Tapatalk
69
« on: March 16, 2024, 03:09:40 PM »
Oil, it should be lubed by the oil in the engine,
I use a HMP grease on the worm drive, because it gets very hot,
Also make sure the cable is smooth, some you can oil, some you can't
Sent from my SM-A546E using Tapatalk
70
« on: March 13, 2024, 03:48:12 PM »
Does the carb have a brass drain screw?
I know the 500 does,
Would suggest you unscrew it, and see if fuel runs out
Sent from my SM-A546E using Tapatalk
71
« on: March 12, 2024, 04:28:29 PM »
I do wonder though if I should warm it up to get any condensation out?
No, Unless it gets to full working temperature, it's likely the moisture will turn acidic, Ideally ride it for the minimum of 10miles, Always get it hot, Sent from my SM-A546E using Tapatalk
72
« on: March 12, 2024, 02:31:02 PM »
Just arrived Sent from my SM-A546E using Tapatalk
73
« on: March 11, 2024, 08:32:47 PM »
Does anyone know if these fit a 1976 cb550 k? I have got the hm323 pipes on and need a new set.
If you have the 323, They will fit Sent from my SM-A546E using Tapatalk
74
« on: March 11, 2024, 04:39:53 PM »
Try a resleeve,,
I am sure it can be done
Sent from my SM-A546E using Tapatalk
75
« on: March 11, 2024, 09:47:12 AM »
Could be they have been "run in" to gently,
And the rings haven't sealed
Sent from my SM-A546E using Tapatalk
Pages: 1 ... 3 4 [5] 6 7 ... 213
|