This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Johnny4428
1
« on: April 19, 2024, 05:11:29 PM »
Looks nice! Bright here up the other end of the country but windy and cold. Not a bike day.
Bright here now in the middle of the country but too bloody cold and windy for a bike ride, or a swim in the sea 🥶🥶🥶🥶🥶
SWIM!! Too bloody cold with clothes on never mind clothes off! 🤣🤣
2
« on: April 19, 2024, 04:05:22 PM »
Looks nice! Bright here up the other end of the country but windy and cold. Not a bike day.
3
« on: April 19, 2024, 04:02:47 PM »
Not a good look Ian especially on a roller. Any car for that matter!
4
« on: April 19, 2024, 11:07:23 AM »
Evidence that this bike has been sitting around for a period of time but nevertheless a nice 400 for someone to purchase, interesting too to see what price it goes for! Anyone on here on the hunt for one?
5
« on: April 19, 2024, 10:40:46 AM »
Nice work there Dave on the clocks and super fast yellow bits!🤣 Always good to see bits and pieces ready for fitting.
6
« on: April 18, 2024, 03:10:52 PM »
Nice one! Looks as if you’ve got some nice weather too! Haven’t had my 750 started yet this year but first chance I get I will get it out of storage fit battery and give it a good check over and out and give it a good warm up!😜
7
« on: April 17, 2024, 10:13:37 PM »
😂😂 not sure about hands free! 😳
8
« on: April 17, 2024, 07:13:26 PM »
My current helmet and bike gear came from them too. No hassles, it was mail order but didn’t have to wait too long if I remember correctly.
9
« on: April 17, 2024, 07:08:06 PM »
Looks like a lot of people and bikes to end up with John. Great to get out!
10
« on: April 17, 2024, 07:05:30 AM »
Worthwhile job on the coils! Having done three sets of coils now I had a couple of leads that just fell out of the ends of the moulding. Interesting how the lower coil in your pic the ht lead snakes in a s formation, must have been the end of a roll before moulding applied during moulding process?
11
« on: April 15, 2024, 06:02:07 PM »
Just got a notification it’s down to $100 dollars for postage about £80, that is shipped with USPS.
12
« on: April 15, 2024, 05:21:35 PM »
That figures indeed Bryan, I made contact with the sellers and they told me they will send it with the Post office.
13
« on: April 15, 2024, 10:32:53 AM »
You would like to think they would be able to withstand a knock or two! 🤣🤣
14
« on: April 15, 2024, 10:31:13 AM »
Just not meant to last Dave!😡 ordered some parts yesterday from the states thought it wasn’t too bad until the postage was added! 😡 Do hope it’s an error!
15
« on: April 13, 2024, 10:31:26 PM »
Well one step forward today and two back! Was freeing or trying to free the piston rings from their grooves, managed the bottom and middle one but unfortunately broke the top ring. I’ll get a new set from the states just $33 plus costs, at least they are available. Will probably order a new fuel tank too which I’m sure I’m going to need. It is fitted within the bottom plinth/base.
|