This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Laverdaroo
Pages: 1 ... 70 71 [72] 73 74 ... 230
1066
« on: February 17, 2023, 12:02:10 PM »
1068
« on: February 17, 2023, 11:59:10 AM »
1069
« on: February 17, 2023, 11:45:20 AM »
Rhubarb and Custard...............simply ace, loved it and still do. Wasn't it Richard Briers who was the voice I cant remember?
1070
« on: February 17, 2023, 11:42:24 AM »
Top fiddling that Ash, they look fantastic!
1071
« on: February 17, 2023, 11:30:43 AM »
PM sent Ted 
1072
« on: February 17, 2023, 11:11:53 AM »
I’ve put a similar thing on mine underneath, one switch has to be in a certain position for the other to work but I. Ths instance it’s that you have to hold it in for 4 secs for it to energise the circuit and allow the ignition to work.
Sent from my iPhone using Tapatalk
1073
« on: February 17, 2023, 11:08:31 AM »
1074
« on: February 17, 2023, 12:56:50 AM »
 Sent from my iPhone using Tapatalk
1075
« on: February 17, 2023, 12:56:19 AM »
Hi all, does anyone know where I can get this stuff from? It’s the sort of stuff they cut holes in for tools in roller cabs, yer know. I can only find it at really expensive money and wondered if an if you lot knew of any going or know of a good outlet for it. I’m after some for packing up the battery in the cradle. on the build and as it’s a lithium one it’s quite small. Also, would anybody have a spare rubber boot thingy for going over connectors in the loom? I’ve not seen them for sale and saved the two I thought I had from old looms for this build. Sadly I’ve been visited by the little furry garage helpers who decided that it was far better to chew up than for me to stick in the new loom leaving me short of one for the front of the bike. It’s one of the bigger ones….  Sent from my iPhone using Tapatalk
1076
« on: February 17, 2023, 12:23:41 AM »
Just had a look after reading that again Ted, yes it's the camera flash, they're not all white, each circuit has i's own individual colour. At least if they're all labelled clearly, then you know which one to pull out and connect to battery to hot wire it  Theres a secret 'dead mans handle' in amongst that lot anyway band they'd have to know the Munit wiring to hot wire it, but a valid point never the less. I fitted the same sort of thing with the 400 install too. Saying that all you haveto do on an OE system is poke 4" of wire into the ignition circuit block at the bars and stick the other end in one of the others (I forget which, have it written dow)to get one to go so this is a distinct improvement
1077
« on: February 16, 2023, 06:32:04 PM »
yeah, there's loads there Ted nothing is cut to finished length,jjust installed to rig up. I leave it as long as possible for as long as possible in case I might have made a mistake and to allow as many routing options as possible. As it's not standard I'm making it up as I go along so any advantage is a good one and by pre empting cock ups they dont become quite as awkward to sort. I'm no auto sparks but its all going well, everything works and I'm rather enjoying it..
1078
« on: February 16, 2023, 03:07:11 PM »
Of course, there'd ne no fun if they werent!
1079
« on: February 16, 2023, 03:05:22 PM »
1080
« on: February 16, 2023, 01:55:50 PM »
Pages: 1 ... 70 71 [72] 73 74 ... 230
|
Show Posts
............