This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - ted_paper
16
« on: April 13, 2020, 09:10:52 PM »
Thanks guys. Looks like motobatt gets the vote 
17
« on: April 13, 2020, 03:14:38 PM »
Thanks for that.I wanted to make sure before I bought.
Stay safe All
18
« on: April 13, 2020, 02:59:22 PM »
Hi
Maybe a stupid question,but is a lithium battery (such as YTX9-BS EXIDE LI-ION LITHIUM MOTORBIKE BATTERY 12V ELTX9) a suitable replacement for the 400/4 ?
Thanks
19
« on: May 04, 2019, 01:34:47 PM »
Old thread I know, but did anyone have any luck with this?
20
« on: October 28, 2018, 08:50:45 AM »
Hi,
I have Kevin's phenolic brake piston fitted for the last seven years and have had no problems with sticking or anything else.
21
« on: August 13, 2018, 01:01:10 PM »
Not sure if DS are the same as Motad, but I had a replacement headers and exhaust from Wemoto (which I believe were Motad) and they were fine until my bike was knocked over when parked and the outside pipe scratched. I got another pipe from Motad but the downpipes now seem to be stainless steel rather than chrome and now has the typical dis-colourisation of s/s pipes.
22
« on: July 17, 2018, 04:49:20 PM »
Hi,
I'm going to be doing a short break from W.Yorks down into Norfolk, along the coast and on to David Silvers before returning home via the Peak District, but I'm struggling to find any information about good routes/roads to incorporate in my route planning.
Are there any members out there who have local knowledge or who can suggest any routes?
Thanks
23
« on: April 24, 2017, 06:31:30 PM »
Went to nearby garage to see if they had anything like it and came away with a Suzuki pattern cover - not a perfect match but near enough. Suppose I'll have to buy enough now to match...
24
« on: April 23, 2017, 08:00:19 PM »
I've tried to measure mine and I'm getting around 65mm internal dia. They aren't marked Stanley so it looks like they are replacements.
Does anyone know which model/make might fit mine?
25
« on: April 23, 2017, 07:21:54 PM »
Thanks Nurse Julie - (BTW I assume you mean 72mm - 720mm is bigger than my dustbin lid  )
26
« on: April 23, 2017, 07:00:28 PM »
Hi All, just found out when trying to replace damaged cover that the front indicator lens cover is slightly smaller diameter than the rear one on my '77 CB400. The new cover is advertised as fitting my bike so I'm wondering if this is this normal or has one been replaced at some stage and if so what is the correct diameter?
Thanks
27
« on: November 05, 2016, 09:21:54 AM »
Sorry Pops, I've been looking for one as well with no luck.
Have you thought about trying to trace the PDFs in Cad?
28
« on: September 11, 2016, 10:39:45 AM »
Thanks for the replies, that seems to clear that up!
29
« on: September 10, 2016, 07:26:23 PM »
So there wasn't a standard fitting for either model?
30
« on: September 10, 2016, 05:50:08 PM »
I have a '77 model and my friend has a '79 model - his has a "pass" switch on his left side controls but mine doesn't. Did Honda change these between the F and F2 models, or has one of us got a replacement fitting?
|
Show Posts