This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - ebmbiker
16
« on: May 26, 2022, 08:13:51 AM »
Found one. Not in the greatest condition, a little rusty but still fine.
I'll send it down to you Friday, I should still have your address.
Absolutely brilliant! Thanks Oddjob
17
« on: May 25, 2022, 10:57:07 AM »
Thanks guys.
Oddjob, yes, that's the one. If you've got one I'll take it thank you
18
« on: May 25, 2022, 08:22:28 AM »
Good day folks,
I'm in need of the now discontinued part 22815-283-000 spring. I've Googled and no joy. Has anyone got one I could buy? If not, is there a known alternative or workaround?
Cheers, JB
19
« on: May 23, 2022, 07:02:17 PM »
Cheers guys. My mate, an electric/electronics whizz, is going to have a look at it and see what can be done with the one I’ve got.
20
« on: May 19, 2022, 09:58:22 PM »
Thanks for the feedback Bryanj, I'll start looking.
21
« on: May 19, 2022, 04:52:54 PM »
Here's what I've got. Tip of the screwdriver is where the wire is broken.
22
« on: May 19, 2022, 12:16:00 PM »
Good day folks,
My stator is in need of repair. One of the yellow 3 phase wires has snapped off and wiring is generally stiff and aged. Can you recommend someone who can fix it for me? It's from a CB500 K1
Cheers, JB
23
« on: April 08, 2022, 04:28:44 PM »
The part on ebay the Sye posted a link to is one of my eBay listings. If you're interested, PM me and I will give you a discount and do post at cost as I won't have yo pay ebay charges.
Thanks for the offer Julie, but your item is far too nice for my project. I’ve found a rusty one that I’ll blast and powder coat. On the subject of removing casting marks, I do. I filed all the casting marks off the R6 fork lowers and triple clamp before they were powder coated. I don’t like parts to look like a sucked boiled sweet, just tidied up. Which reminds me, I should start a post in the Project section
25
« on: April 05, 2022, 09:41:25 PM »
Cheers Trigger, why didn’t I think of that?!
26
« on: April 05, 2022, 09:09:30 PM »
Good evening folks,
As my CB500K1 came in pieces, in boxes, I’ve got a couple of things missing. I’m missing the rear brake actuator arm and kickstart lever. Are these parts common across a few Hondas of the era?
If so, which ones? So I can start looking.
Cheers, JB
27
« on: March 23, 2022, 01:24:26 PM »
No surprises. I took part in Goblin Works Garage once and the whole thing was scripted and staged from start to finish. But it does make entertaining TV!
28
« on: March 07, 2022, 05:18:31 PM »
Don't worry about the fiché, I have both here
(Attachment Link)
Brilliant, PM sent
29
« on: March 07, 2022, 01:51:22 PM »
Good afternoon folks,
Gradually getting all the parts I need to rebuild my engine. When I bought the bike it was already disassembled, including the engine. I've been through all the bits and can't find the tranny bearing retainer half rings, part numbers 13491283000 & 13492283000. I can get the latter item from CMS but the other item is no longer available.
Are these available anywhere? If not, is there a known solution?
Cheers, JB
30
« on: March 05, 2022, 08:29:17 PM »
And I've received mine as well. Cheers Erny
|
Show Posts