This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - El__burro
46
« on: April 27, 2015, 11:55:07 PM »
Hello, having to replace the fuel tap (due to a mission spout) I am looking for a replacement part.
Does any other model fit k2 version?
Regards
El__Burro
47
« on: March 25, 2015, 03:36:41 PM »
I am trying to figure out what way do the front fender go. Please have a look at the picture to see if I am making a mess. The other thing is the rear shocks. I am having big problems with the nut to hold them in place. I have tried 17cm bolts but they are too small, the next size up is too lose. Any idea? Thanks El__burro 
48
« on: March 08, 2015, 12:06:36 PM »
Hello, I am looking for a cb750 k2 side cover (battery side). Would this cb500 fit? Thanks El__burro 
49
« on: February 04, 2015, 07:57:50 PM »
Ooooooh yeah!  After many kicks the oil pressure light went off. Then the magic happened. Just wanted to share with you the first time it roared and what a ROAR. For sure it needs some adjustments to be fully satisfied but my ambition was to start the engine and hear its roar. Mission accomplished. Thank you el__burro
50
« on: January 31, 2015, 09:48:28 PM »
Hello having f****d up my brake callipers i am looking to replace them with a decent pair ( i am not on a rush but..)
I'll be browsing the net to see if a pair comes up at a decent price.
My bike is a K2 are other model suitable?
Does this forum have a part swap or sale session?
Regards
El__burro
51
« on: January 31, 2015, 08:59:21 PM »
Hello, I am trying to get the fuel tank clean and sealed. When I removed the fuel tap i noticed that one of the spout is missing and the other came off quite easily. Is it normal? Can I just buy the missing spout?  Thanks El__burro
52
« on: November 27, 2014, 11:50:56 AM »
Hello, i have been looking for some drawing plans to make an engine stands for cb750 k2.
I have some scrap metal i could put to a better use.
Searched on google but nothing with measurements.
Does anyone have any plan or a link to some
Thanks
53
« on: November 14, 2014, 06:39:32 PM »
Hello, I am looking to purchase a dual/twin throttle control for my cb750.
Ideally I would go for a Tomaselli domino as I have this mounted on another bike and i find it ok. Unfortunately budget restrictions apply.
I have come across the Doherty 77 replica but it's so cheap that I am a bit hesitant.
Anyone has used this or have some feedback to share.
Thanks
El__burro
54
« on: November 04, 2014, 10:45:46 PM »
Hello, how easy is to relocate the front brake master cylinder away from the bars (k2)
Thanks
El__burro
55
« on: October 04, 2014, 12:43:25 PM »
I am curious to see if the engine is in working order (and mainly want to hear it roar) Is there a way to start it without mounting all the bits and pieces ie coils end the rest of the wiring diagram. In other words what is the minimum necessary to start it? Thanks 
56
« on: October 04, 2014, 12:33:42 PM »
Trying to create a sort of cafe racer/brat cb750k2
Just looked into some clip on bars but i am not sure they'll all fit.
What diameter are the stock fork?
Also can anyone recommend a brand or a shop.
Thanks
57
« on: June 30, 2014, 05:41:14 PM »
Hello,
Are the ignition key and the steering lock the same?
(assuming that they are original)
Where can i buy or get a copy of one.
Thanks
El__burro
58
« on: May 15, 2014, 10:34:59 PM »
I am about to deal with removing damaged screw to remove the exhaust from the header.
So far I have managed to remove 3 out of 8 (almost easily).
I have now 5 damaged screw to remove, what is the best way to do this?
Thanks
El__burro
59
« on: May 08, 2014, 09:55:43 PM »
I am just looking at my new project (CB750 K2) and putting together a parts wish list.
I'll need some valve caps (the bolts that cover the valve)
I need also a top yoke, mine has a crack at the tightening bolt.
for sure I don't want to buy a similar one (with the rhino horn).
What other models do adapt to this model (even not Honda).
Thanks
El__burro
60
« on: May 08, 2014, 09:35:49 PM »
Hello,
I am looking to sort out an issue I have with the fuel tank locking latch
The catching piece of metal is not there and I am guessing if I can replace it completely with a different cap.
Thanks
El__burro
|
Show Posts