Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Deano400

Pages: [1] 2 3 ... 30
1
Misc / Open / Re: Stop/Tail light issue....electrical genius needed..
« on: March 22, 2024, 11:09:53 AM »
Have you made any progress with the permanent taillight?

You say you have checked the connections at the taillight and that they are ok. These connections are from a sub loom, have you checked the connections at the other end, under the seat?

Not sure it’s possible to connect the black feed to the brown taillight feed as the connections should both be female but it’s worth checking (in the head light bowl).

It is worth checking the function of the ignition switch but in my (limited) experience problems with the ignition switch usually lead to things not working rather than working when they shouldn’t.

The taillight works separate from the head lights and is powered with the pilot light (small separate bulb) in the head light bowl. Is the pilot light on when the taillight is on?

Is the pilot light bulb ok?

Does the taillight go off if you disconnect the front or rear brake light switch?

Are the speedo and tacho lights working ok?

An easier mistake for someone to make would be to cross connect the brown and brown/white connectors in the head light bowl.

Lot of questions but as Bryan says it’s not easy to diagnose electrical issues at a distance.

Not sure what work was done on the bike and whether there was any reason for anyone to disconnect any wiring unrelated to your engine refurb.

2
CB350/400 / Re: Alternator loom clip
« on: March 16, 2024, 07:59:57 PM »
Good news Ash. Always worry about loosing bits in the post that aren't easy to replace.

3
CB350/400 / Re: Parakeet Yellow Paint Code
« on: March 15, 2024, 03:39:19 PM »
Dave,

I don't know how reliable this site is but they give the following code:  Color Code: Y-31   No. QE   Color Code Name:  Parakeet Yellow

https://www.motorcyclespareparts.eu/en/honda-parts/honda-color-codes

4
CB350/400 / Re: Alternator loom clip
« on: March 14, 2024, 11:30:07 AM »
Hi Ash,

Posted this morning. Only had a second class stamp though but hopefully you'll get it by Christmas.

5
CB350/400 / Re: Alternator loom clip
« on: March 13, 2024, 08:21:38 PM »
Hi Ash.

Will need a clean, bit of heat and gentle persuasion to get back into shape and then plating. If you want it, PM me your details and I'll get it in the post.

[ Guests cannot view attachments ]

6
CB350/400 / Re: Engine rebuild Parts list
« on: March 11, 2024, 08:17:24 PM »
Ok, from the measurements it's 1 Brown, 4 Green.
Like you say order a set and plastigauge to check.

7
CB350/400 / Re: Engine rebuild Parts list
« on: March 11, 2024, 05:27:29 PM »
When you say the clearance is 0.01124, do you mean the crank measured 31.98876?

8
CB350/400 / Re: What is this cog called?
« on: March 08, 2024, 12:31:46 PM »
Countershaft Top (6th), the gear to it's right is countershaft 2nd.

9
CB350/400 / Re: Alternator loom clip
« on: March 08, 2024, 10:34:20 AM »
[ Guests cannot view attachments ]


10
CB350/400 / Re: Alternator loom clip
« on: March 08, 2024, 10:26:54 AM »
Is this any use Ash?

[ Guests cannot view attachments ]

11
Misc / Open / Re: DONATIONS
« on: March 07, 2024, 12:20:48 PM »
Done.

12
CB350/400 / Re: Engine rebuild Parts list
« on: March 06, 2024, 04:37:52 PM »
You have written 1 1A 1A 1A 1A 1A in your post. I guess the extra 1A is a typo.
All 1s on the crank and BAAAA will give you 1 Green and 4 Yellow for the mains.
You need to match the letters (4 As) on the crank with the numbers on the con rods to get the big ends.
The letters on the conrods are the weight and should all be the same.

I'm sure someone will put me right if I've got mixed up.

13
CB350/400 / Re: My New Project arrives after a 44 year wait!
« on: March 05, 2024, 08:08:39 PM »
Thanks Dave.

14
CB350/400 / Re: My New Project arrives after a 44 year wait!
« on: March 05, 2024, 07:56:16 PM »
I agree with Ash the Yellow pasivation is brilliant - how did you do the steel carb blanking plugs - presumably you had to remove them?

They press out pretty easily Ted.

Ash, would you recommend any sort of sealant when replacing the caps or is it just a matter of pressing them back in?

15
Misc / Open / Re: From the bowels of Graham's tool chest 😁😁😁
« on: February 03, 2024, 03:50:28 PM »

Pages: [1] 2 3 ... 30
SimplePortal 2.3.5 © 2008-2012, SimplePortal