This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - hondatri
1
« on: September 19, 2018, 08:30:25 PM »
Thanks Guys I got hod of 5 ltrs of Mineral oil.
2
« on: September 15, 2018, 02:41:23 PM »
Clutch Sorted Thanks guys for Info
3
« on: September 15, 2018, 02:37:42 PM »
What oil should I use in my 77 400/4 I know 10/40 but what bout synthetics and Semi Synthetics,
4
« on: September 05, 2018, 05:13:46 PM »
Thanks for pointing me in right direction.Much appreciated
5
« on: September 04, 2018, 07:35:43 PM »
No Iam just wondering if there is a push rod to operate clutch ( I am used to older bikes not familiar with the 400) I am just thinking that their should be a rod there before I fit springs and Plate. When I fit the new plates and tighten up and lock the castellated is there a push rod or does anything go through the hole.
6
« on: September 04, 2018, 04:11:18 PM »
Hi The old Fart is Having a Senior Moment. Is there a push rod going through Hole through lock nut. I dont see one in Parts listing.
7
« on: September 04, 2018, 10:13:07 AM »
Thanks To All for the help and Suggestions I got one from Wemoto but too big, I will keep site informed,
8
« on: September 03, 2018, 07:49:20 PM »
Hi The Old fart is back.My Yellow Pearl was idle for a while and she is leaking oil past the Gear GChange shaft. so I want to replace Oil seal but cannot find a P/N number anywhere Dave Silver and CMSNL only show kits anyone know P?N there is a number on the seal NGK174 SC14 24 15 4.Anyone got any ideas on P/N.
9
« on: August 11, 2015, 02:03:51 PM »
Thanks for the info and Confirmation Now I better get on with the Job.
10
« on: August 10, 2015, 07:59:00 PM »
Hi guys the pest is back I am painting my 1977 yellow 400/4 Tank and Side panels I have them painted and Lacquered and now want to fit the new Decals. I bought these from Classic motorcycle decals about 3 years ago now ready to fit them. Can anyone give me advice on fitting
I think they are to be put in water to remove from backing. Any advice would be appreciated. My son says to put soapy water on tank to help move around would that be right. Any advice or tips
Pat Lackey
11
« on: January 27, 2015, 07:33:15 PM »
Getting there with the Old Girl. Got the Carbs on today with help from my Son. Two heads and four hands are best.
12
« on: January 22, 2015, 08:19:02 PM »
A french man touring Ireland came to a cross roads and not sure which road to take he approached two locals sitting on wall. Parle Vous Francois got no reply so he says Deutch still no reply Italiano.then tried Espanol getting no reply he got back into car and drove off, One local turned to the other and said "Mickk do you think we should learn a foreign language" Not at all Pat sure your man knows four and it got him nowhere.
13
« on: January 22, 2015, 02:23:02 PM »
Hi guys I hope someone can help. My Son has a 2011 Honda Varadero with an intermittent speedo and ABS. In cold weather it works for a few miles then the speedo fails and ABS light comes on. He has cleaned contacts and sprayed all connections with WD40. But problem persists. It can come ok anytime then fail again. Any ideas.
14
« on: January 20, 2015, 07:11:54 PM »
Its all in the terminology guys. Washer/Shim it appears on very few engines apparently. Why I dont know
15
« on: January 19, 2015, 08:01:44 PM »
I dealt with Dennis at noxandrattles who supplies Stainless Parts for 400/4 He told me he had stripped lots of 400/4 engines and never came across a washer on the camshaft, Today he contacted meto let me know he was doing the Topend of a 400/4 and lo and behold there was a a washer on the camshaft.
|
Show Posts