This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - hondatri
16
« on: July 21, 2014, 07:26:25 PM »
An elderly couple were celebrating their Golden wedding anniversary and went back to the village where they met. They were walking down a Lane when she stopped him and said Remember you took advantage of me against that fence. I sure do he said. She said will we do it again for old times sake. Why not he said so they went at it and the old boy was going like a rabbit. When they stopped she said You were not as good as that 50 years ago. He replied That fence was not electrafied 50 years ago.
17
« on: July 01, 2014, 04:25:55 PM »
Me again guys have not got near clutch yet now I have found another problem. I went on a charity run a few months ago we were advised to ride with headlights on after 28 miles my Battery was dead I Charged it up and it seemed ok until I put headlight on. I took battery out yesterday and found that water level was near bottom I topped it up with distilled water and charged it up. I left it disconnected overnight and this am voltage was 12.3v I went for a run of 15 miles and when I got back Batt was 11.94. I connected an ammeter in series with Pos lead and got following Readings. Idle 0A 2K=2A 3K=4A and 4K= 6A. When Headlight put on Charge was 0A at all revs. Reconnected Battery and got following Voltages. Idle=11.64, 2K=12.08, 3K=12.50 4K=12.80. With head light on the voltage never went over 11.75V. I have a Haynes Manual and am going to check Alternator out put I had a look at voltage reg. and cleaned contacts it is the non adjustable one. Has anyone got any ideas as to what I should look out for.Should I get a new Battery first.
18
« on: June 30, 2014, 07:45:51 PM »
85 year old man goes to the Doctor. I want you to lower my sex drive Doc he said. The Doctor replied, At your age its all in the mind. I khow said the man I want you to lower it.
19
« on: June 29, 2014, 08:59:23 PM »
A policeman pulled a Lady over and asked to see her licence. I see here you should be wearing glasses he said. She replied I have contacts to which he replied I dont care who you know you are still getting a ticket.
20
« on: June 22, 2014, 09:16:05 PM »
I have a 91 Kawasaki GT550 the engine of which is rattly. I replaced the timing chain with no improvement The noise reduces as the Engine warms up. It has been suggested to me that it is the Clutch Basket anyone have experience of this.
21
« on: June 22, 2014, 09:10:16 PM »
Hi Guys I am looking for some info on my 77 400/4. Whenever I let out the clutch I get a jerking as Drive picks up. On moving off I let in the clutch the drive takes up with a Jerking Thump same when changing gear. Otherwise riding is ok. Any suggestions appreciated.
22
« on: May 22, 2014, 01:49:54 PM »
My 77 400/4 is running rich and plugs fail after a while I am going to remove Carbs (God help me) to clean and adjust them, is there a simple way to remove carbs. I have a small sonic cleaner but dont know what liquid to put in it to clean jets. I have the use of a vacuum set for synchronizing. Also the Timing chain is noisy and want to do a job on it at the same time and replace chain/guides/and adjusters can this be done with eng in frame. Any info appreciated.
23
« on: March 24, 2014, 08:01:04 PM »
I am trying to help an elderly neighbour get his cyclemotor going again. It is a Bernardi engine that bolts onto bicycle driving the back wheel. It was not pulling so he asked me as I have bikes to have a look at it. I found the two piston rings broken and Have been looking for 2 or for a piston and rings. The Piston Dia is 34mm. The Engine is a BERNARDI made in Italy European Patent 82830113 5.
I would appreciate any help in locating parts. I would like to get the Old Boy Mobile again as I miss seeing him potter around on it. You were likely to see him anywhere on it
24
« on: March 24, 2014, 07:45:24 PM »
Hi guys my Sons Blade has blown its Voltage Reg. I have a new one but the 2way connector on bike loom into which Reg DC output connector is connected is Burnt and I would like to replace it. But honda agents say I must buy the loom expensive, The connector is an 8.25 connector anyone know where I can get one.
25
« on: January 21, 2014, 06:38:03 PM »
Hi from a newbie I have been given a box of Genuine Honda parts in original packaging I was told they for 400/4 or CB750 Is there any place where I can Check the Part numbers to see what they are and for which bike Some are bushings and some are seals.
|
Show Posts