This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Davelu88
136
« on: July 29, 2022, 07:43:19 PM »
Got cover off with rubber mallet , but this washer fell out ? Looked at schematics but still not sure as don't seem to fit anywhere.
137
« on: July 28, 2022, 02:03:04 PM »
Many thanks Oddjob, 😊
138
« on: July 28, 2022, 01:46:51 PM »
Hi All , after alot of swearing and threatening to scrap the bike the engine has finally let me get out all the screws holding the clutch cover on , however it does not want to let go of the cover so easily, anybody got any tips to get it off as I think this maybe the first time it has been apart .
Thanks Dave
139
« on: July 07, 2022, 08:12:43 PM »
Finally got it all sorted with a genuine kit from DS , the top and bottom races tapped in fine although I did freeze them for an hour or so but it all fitted great , expensive but worth it me thinks 🤔
140
« on: July 03, 2022, 01:54:26 PM »
I think I naively thought that when I bought something that said 550F it would be plug & play & not generic , anyways have had to dig deep and purchase the genuine kit from DS. Lesson learnt and thx for all the advice:)
141
« on: July 02, 2022, 10:24:42 PM »
I would say about 3 mill
142
« on: July 02, 2022, 10:15:54 PM »
race in frame then bearings in that then race over stem then dust cover , if I put thick washer on the bottom I did not have enough thread at the top so left washer out so then I had plenty of thread but when tightening dust cover up to its max I still had up and down play . I wonder if I need a thin washer at the bottom ?
143
« on: July 02, 2022, 09:31:50 PM »
Hi No just captive ones
144
« on: July 02, 2022, 05:40:42 PM »
What am I doing wrong , I have fitted top and bottom races and I'm sure they are seated all the way in , but when I screw down the top dust cover I cannot get it tight enough to stop the yoke from moving up and down . Help please it's driving me nuts
145
« on: June 29, 2022, 09:19:54 PM »
Will do 
146
« on: June 28, 2022, 08:26:41 PM »
Thx for all the advice , I do like the sound of the captive ball ones on ebay .
Bryan do these ones come complete with the races etc .
147
« on: June 27, 2022, 09:35:02 PM »
Hi all this is off my 550F it's in very good condition with no rips etc but I have taken the catch off etc . How does £40 plus postage sound if any one is interested, I also have a kerker exhaust with downpipes that I will put on soon .
Regards Dave
148
« on: June 27, 2022, 09:20:55 PM »
Thanks Bryanj but disaster has happened, I have been too heavy handed and whilst trying to hit them in with a socket I have broken the top one & damaged the bottom one. I have them out now , are tapered ones easier to fit . Thx
149
« on: June 27, 2022, 07:25:12 PM »
Hi all , the powder coaters removed my races when he did my frame , I have got them back in but do they sit flush or are they recessed . Thanks Dave
150
« on: June 21, 2022, 09:13:45 AM »
Cerakote is a nice finish , I have been searching old threads and another member said they used Simonez tough satin so I will give it a go I did consider powder coating but like Trig said I thought it would be too thick . Let's us know how it turns out
|
Show Posts