This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - bobthebuilder
16
« on: July 25, 2012, 08:35:08 PM »
Hi Guy's, Nice to see it's all been worth the effort, have a k2 that needs a bit of work so that will be next, but you never know what might turn up in my shed, trouble is I need a bigger shed,  Jock.
17
« on: July 24, 2012, 11:13:43 PM »
HI Guy', Hope it works this time, Technology is a wonderful thing when you know what to do with it, and I don't.  Jock.
18
« on: July 24, 2012, 10:43:03 PM »
Hi Guy's, Got it wrong way round, better stick to working on bikes, not much more to say will just post pics. Most of the pics seam to be too big to post will get some more looked out that I hope will work, hope you get the idea.  
19
« on: July 24, 2012, 10:21:15 PM »
Hi Guys, Do any of you remember this, when I first posted pics, one of you jokers said they admired a man who liked a challenge, well it sure was,it's taken 3 years, and a lot of blood,sweat and tears, and of course don't forget the money, but have learnt a lot along the way, will post the after pics in next post. Jock.
20
« on: January 13, 2012, 06:47:23 PM »
Hi Guys, Got problems with split overflow tubes on carbs, dose anyone know best place to get fuel resistant heat shrink tubing. Cheers Jock.
21
« on: December 27, 2011, 07:19:43 PM »
Thanks Pete,
Ordered many thanks,
Cheers Jock.
22
« on: December 27, 2011, 05:53:07 PM »
Thanks All,
Next question where is best and cheapest place to get it.
Cheers Jock.
23
« on: December 27, 2011, 04:23:51 PM »
Had seen this advertised and getting good reports, would you recommend spray or the pump action bottle for best results.
Cheers Jock.
24
« on: December 27, 2011, 11:04:34 AM »
Hi. Guys, Have to move one of the bikes outside over winter, need room in the garage, anyone tried vaseline on alloy, or any better tips to stop the alloy from pitting and corroding, damp had got to it already after hours of cleaning.  Cheers Jock.
25
« on: November 06, 2011, 11:48:19 AM »
Hi Guys, Came across this site on the web Caswell Copy Chrome and was wondering if anyone has any experience of using it and what were the results. www.caswellplating.comCheers Jock.
26
« on: September 27, 2011, 08:13:18 PM »
Hi. Bryanj, Advice spot on faulty Kill switch, stripped down cleaned terminals sprayed with WD, reassembled pressed starter, LOVELY spark at plugs. Thanks again Jock.
27
« on: September 25, 2011, 05:36:20 PM »
Great, will check 12 volts and kill switch in morning Hope that solves problem, will keep you posted. Cheers Jock.
28
« on: September 25, 2011, 04:41:34 PM »
Hi Guys, Fired the engine up on KO after rebuild, but had to shut down with bad fuel leak on No. 4&2 carbs. Fitted new float seats and needles, now ok but have no spark at plug leads, fitted new condensers and checked timing but still no spark, dose this just leave coils as main suspect or should I be looking elsewhere, would appreciate any input. Cheers, Jock.
29
« on: August 24, 2011, 08:13:43 PM »
Cheers Mick,
Will do. Jock.
30
« on: August 24, 2011, 06:13:48 PM »
Hi Guys, Went and had a look at American cousins sohc posts, and there was quite a bit about nos parts from Asia and else where, and a great deal of posts from our own Ash, with a lot of info, but they were about 2 yrs old, any more up to date info or are things still the same, that Ash sure gets around.
|
Show Posts