This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - paul G
Pages: 1 ... 102 103 [104] 105 106 107
1546
« on: October 15, 2013, 08:38:26 AM »
Hi,
Just starting the rebuild of a spare engine which I bought last week, this is turning out to be a bit of a bargain.
It has had a recent rebuild and re bore with new cam chain guide and tension er.
I don't know how many miles it has covered since the re-bore so going to re ring it.
Been on silvers but not a stock item, there is a set on eBay but it states not suitable for a K3 model, does anyone know the difference between the models.
Regards,
1547
« on: October 13, 2013, 05:02:25 PM »
Mickwinf,
That link is brilliant, did it today.
Starter cluch repaired without breaking the engine, the link is spot on and easy to follow.
Thanks for your help.
1548
« on: October 12, 2013, 04:02:07 PM »
Ken payment sent via PayPal thanks all for your help.
Regards
1549
« on: October 11, 2013, 08:32:10 AM »
Bista,
As above with Odjob can you pm me your details and how much you want for the stopper.
Regards,
1550
« on: October 11, 2013, 08:19:45 AM »
Odjob,
Thanks can you pm me your details and how much you want and payment method.
While you are trawling through your bits have you come across the clutch adjusting screw that goes through the casing to the lifting arm.
Mine is quite chewed up, casing got to come off again to do the starter clutch.
Regards,
1551
« on: October 09, 2013, 08:30:11 AM »
Oddjob,
It's not urgent so anytime will do
.
Thanks
1552
« on: October 08, 2013, 11:33:23 PM »
As Ewan says the part numbers do look the same but still unavailable for all the listed models so if anyone has some spare I would be gratefull
1553
« on: October 08, 2013, 12:38:30 PM »
Busa,
Thanks, got the chain adjusters new from silvers but the chain adjuster stops are discontinued.
If not then I think I will be calling in on our toolmaker at work.
Regards,
1554
« on: October 08, 2013, 12:36:27 PM »
Mick,
Thanks for the effort and help, that is exactly how it sounds.
Will give it a go when I get the parts.
Regards,
1555
« on: October 07, 2013, 08:21:21 PM »
Mick,
Does this mean a full strip down ?
Regards
1556
« on: October 07, 2013, 07:15:19 PM »
Hi,
Are the starter motors on the 550 range the same.
I have a problem when starting the bike, it sounds as though some of the teeth are stripped loud grating noise.
Checked the teeth on the starter and the starter gear reduction through the starter motor hole.
All looks ok so just wondering if they are all the same, I fear they are !
Thanks
1557
« on: October 07, 2013, 12:14:14 PM »
Thanks for the info Mick
1558
« on: October 06, 2013, 08:54:17 AM »
Hi,
I have PD carbs. Does anyone know the jet sizes and needle settings for a 77 K3 .
I have the manual but this does not give them for a K3
Is the float height 14.4 for these carbs.
Thanks
1559
« on: October 04, 2013, 12:39:45 PM »
Hi,
Has anyone got a spare set of stoppers for the chain adjusters.
Been on silvers and they are no longer available, does any other model fit !!
Regards,
1560
« on: October 01, 2013, 12:28:44 PM »
Got the tank prepared at the weekend and put the new decals on. how bloody nerve wracking was that.
Pages: 1 ... 102 103 [104] 105 106 107
|
Show Posts