This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Arch stanton
Pages: 1 ... 21 22 [23] 24 25 ... 27
331
« on: June 07, 2018, 11:13:44 PM »
Hello Folks.
Are there any differences between the front Hubs on the.
Cb500, 550,& 750f1?
Your inputs would be greatly appreciated.
Sean.
332
« on: June 05, 2018, 05:01:33 PM »
That is exactly what I'm trying to achieve. Only on double disc set up.
I'm really don't like the hoses going round the outside of the forks.
Thanks for posting.
Regards.
Sean.
333
« on: June 04, 2018, 11:32:18 PM »
Cheers.
I was thinking they may have used something odd
Similar to yamaha on the RD's.
Sean.
334
« on: May 27, 2018, 03:35:53 PM »
Yes.
Thanks for that Dennis.
I think I'll have three.
Sean.
335
« on: May 27, 2018, 12:03:01 PM »
Hello Dennis.
Thanks for the info.
I have one F1 caliper. In fact I had two but I think I chucked it out in a clear out thinking a would not need F1 Calipers in the future.
Goes to show, you never know.
Dave Silver currently list them as out of stock.
Sean.
336
« on: May 27, 2018, 09:12:59 AM »
Is there a later K series caliper that matches the F1?
Or are The Calipers on the F1 unique?
Sean.
337
« on: May 26, 2018, 12:06:10 AM »
Looks like I'm gonna have to glue mine. As some idiot in the past cut the tabs off the tank.
Sean.
338
« on: May 26, 2018, 12:03:25 AM »
It's a start.
Cheers Rob.
339
« on: May 25, 2018, 10:29:46 PM »
Can anyone tell me the thread size & pitch in the hole where the brake pipe enters the Caliper on a Cb750f1?
As the threads on the Caliper I have is a bit festered & needs cleaning out.
Sean.
340
« on: May 23, 2018, 01:30:54 PM »
Someone once asked me.
What is the best method of replicating the factory finish on
Yamaha Rd frames.
I said use no primer, a quick blast of black. Then throw a handful of sand at before it dries.
Then another wiff of paint to finish. Perfect!
341
« on: May 22, 2018, 10:10:36 AM »
Everything else is straight & true. So I doubt its due to accident damage.
But going by the state of the dreadful welding. I think its down to poor manufacturing.
Let's face it. If quality control would pass that welding. They would pass anything.
Sean.
342
« on: May 21, 2018, 01:40:07 PM »
Has anyone come across this??
I have stripped down my K1 frame ready for paint.
But rhe Bridge over the rear of the frame is pissed.
Looking from the rear. The bridge is about 10mm higher on the left.
This can only be a manufacturing fault.
As the frame rails are straight & measure the same distance apart as my straight F1 frame.
Has anyone noticed any anomalies like this?
Sean.
343
« on: May 19, 2018, 01:15:47 AM »
Hello Simon.
Yes my F1 had filters hidden away above the inlet needle valves.
Sean
344
« on: May 17, 2018, 10:02:36 AM »
Thank you for your response.
It will be of great assistance.
Thanks again.
Sean.
345
« on: May 17, 2018, 06:13:49 AM »
Very useful info.
That should have sorted that problem.
Thanks to all.
Regards.
Sean
Pages: 1 ... 21 22 [23] 24 25 ... 27
|
Show Posts