Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - billy192

Pages: 1 ... 4 5 [6] 7 8 ... 21
76
CB750 / Re: Oil bloody oil
« on: September 04, 2014, 11:46:46 AM »
no it does have it i did not know what it was but do now.
Billy

77
CB750 / Re: Oil bloody oil
« on: September 03, 2014, 08:16:37 AM »
thanks Guys i will investigate this weekend
Billy

78
CB750 / Re: Oil bloody oil
« on: September 01, 2014, 09:28:11 AM »
mmmm thanks LOBO never looked at the chain oiler. my back wheel has oil on it to, not much but deff some. theres no drips on the floor in the garage as its parked in the same place for a week at a time (only use on a sunday).

some more dots of oild under th carbs on the clutch side also.
thanks for the advise
Billy

79
CB750 / Oil bloody oil
« on: August 31, 2014, 08:44:42 PM »
I have done about 2K on the K6 without any problems but now after a run (about 50-60) miles i get spots of oil on the finn below the head gasket but it has not run from there. it seems to have been blown i think and its on both sides

i use a quarter of a pint of oil in 150 miles.

where is this coming from?
does this mean my head gasket is shot?





80
CB750 / Re: dishwasher
« on: August 16, 2014, 08:18:08 PM »
well got it and did a few trial runs. first with the finish tabs (other good products are available)
and the it went a bit black, but after washing again with washing up liquid it went back to original. next tried a 1/4 pint of ultrasonic cleaner. did not go black but did not clean much oil off
then tried dish washer cleaner from the pound shop and a little squirt of fairy.

look for yourself. i think its good enough for painting.



dirty



clean.
Billy


81
CB500/550 / Re: CB550K3 - Fork Springs - Which way up?
« on: July 25, 2014, 08:21:53 AM »
my Little G5 had forks that were sticking. when i removed the mud guard, front wheel (with jack under engine) i slackened the triple clamps and as i turned the stanchions the end where the spindle was moving in a circular motion. meaning my forks were ever so slightly bent. it must have had a tap on the front end in its 30+ years.
i turned them til they both pointed forward the most tightend up and boom work great. i will replace when i can afford.
not saying yours are the same but worth a check
Billy

82
CB750 / Re: dishwasher
« on: July 22, 2014, 11:45:49 AM »
do you think it will get all the grime off the parts, if only enough to get clean enough for paint?
Billy

83
CB750 / dishwasher
« on: July 22, 2014, 10:05:03 AM »
Ok so I have been caught using my wifes dishwasher with bits of my CB500T.
my question, i bought my own dishwasher for the garage would i do any harm if i put things like cylinder head (stripped obviously) has anyone tried things like a head and barrels in a dishwasher? would it warp it?
Billy

84
CB750 / Re: dripping tap
« on: July 21, 2014, 06:41:45 AM »
All I can do is get a new one


just ordered one from DS £76.60 ouch

Sent from my iPhone using Tapatalk

85
CB750 / Re: dripping tap
« on: July 21, 2014, 06:23:24 AM »
Mine has no screws for the fiberes it is quiet new


Sent from my iPhone using Tapatalk

86
CB750 / dripping tap
« on: July 20, 2014, 07:52:12 PM »
my petrol tap is dripping even when off. not much but enough to drip out of the exhaust when starting up after a week.

is there any way to adjust/tighten ?
Billy

87
CB750 / Re: miss at 3.8K
« on: July 12, 2014, 09:08:01 PM »
thanks Guys, you all have helped make me smile.  8) ;D

Billy

88
CB750 / Re: miss at 3.8K
« on: July 11, 2014, 01:20:04 PM »
fantastic news, well to me it is. fond the vents and as i described there was a clear pipe joining them (making it air tight)
removed the pipe and connected up the 4 over flows and bingo great acceleration all the way to 90ish
just went to Swindon and back its like a different bike it idles smoothly also.
billy, happy chappy


89
CB750 / Re: miss at 3.8K
« on: July 10, 2014, 08:50:34 PM »
when i had-my carbs back from the guy that cleaned and rebuilt them there was a tube joining #3 and #2 sealing them should these vet out to the air box?
Billy

90
CB750 / Re: miss at 3.8K
« on: July 09, 2014, 09:24:19 PM »
Bryanj do you know where the vent is?

Billy

Pages: 1 ... 4 5 [6] 7 8 ... 21
SimplePortal 2.3.5 © 2008-2012, SimplePortal