Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Dolomite_

Pages: [1] 2
1
CB350/400 / Clutch adjustment
« on: March 26, 2020, 06:26:26 PM »
I replaced the clutch plates a few months ago and ive been trying to set the clutch up to my liking but I've had to put the bar end and clutch end bolts really far out to get the clutch to disengage fully. I've tried adjusting the screw and lock nut on the arm mechanism but have only been able to move the biting point about half way from the bar. I know this isnt right.

 Is this a sign that the clutch spring bolts aren't tight enough?

 What is the typical amount each clutch adjustment bolt should be screwed in?

2
CB350/400 / Re: Cb400 four indicator wiring
« on: March 10, 2020, 06:29:13 PM »
I forgot about the rubber mounting for the rear lights, so thats why they dont work. Well in the end somehow the relay had died, tried a spare one I luckily found and the front ones flash now. Thanks all.

3
CB350/400 / Re: Cb400 four indicator wiring
« on: March 09, 2020, 08:03:35 PM »
The grounds for the indicators are fine as I managed to get them to light up solid. But the only way I could get them to light up was by crossing the 2 connections on the indicator repeater (aftermarket one with no ground connection). Both connections do have a voltage and I get a reading on the gray wire in the switch on the bars but when I flick it left or right I lose the voltage on the gray wire and nothing shows in the blue/orange wire.

4
CB350/400 / Re: Cb400 four indicator wiring
« on: March 08, 2020, 01:12:28 PM »
Have you got all the wires earthed (green wires) correctly through the earth tabs each side on the inside of the headlamp bowl?

I'm guessing the indicators are aftermarket as they dont have an earth wire coming out of the indicator housing so they are grounded at the end of the indicator storks where I have took some paint off.

5
CB350/400 / Cb400 four indicator wiring
« on: March 08, 2020, 12:41:45 PM »
I have a few issues with the wiring that I just cant get my head around so wanted to see if anyone has had any similar problems. The indicators arent working. There is voltage on the black and gray wire going out/in the indicator repeater and im getting a voltage reading on the gray wire at the switch on the bars but when I flick the switch to left and right I lose the voltage. The headlight and brake light turn on so I know the wiring is working.

6
CB350/400 / Re: Rear brake retaining spring.
« on: January 15, 2020, 06:59:48 PM »
Thanks all. Got that job ticked off, now onto the next one.

7
CB350/400 / Rear brake retaining spring.
« on: January 05, 2020, 04:35:37 PM »
I've referenced some pictures and It appears that I have the retaining spring next to the rear brake lever in the right place but there still seems to be quite a bit of play in the brake lever. The adjuster nut on the wheel end is compressing the spring that end quite a lot and if I keep turning the nut to take out the play it will be fully compressed.

Could anyone upload some pictures of the 2 springs so I can compare?

8
Desperately Seeking!! / CB 400 four collector box.
« on: November 05, 2019, 09:36:50 AM »
Does anyone know if collector boxes are available excluding the down pipes.Or if anyone has a spare collector box around?

9
CB350/400 / Dunstal replica exhaust
« on: November 03, 2019, 06:11:45 PM »
Has anyone had experience with the dunstal replica silencers such as the the ones listed on classicbike shop: https://www.classicbikeshop.co.uk/catalogsearch/result/?q=dunstal . Have you had any issues with the inlet adapters or have they been fine?

10
It seems to be as loud on either side of the engine so that made me think it was the primary chain. I read on another post about out of sync carbs causing an issue but they were all set up correctly when I got them rebuilt. Clutch rattle might be a possibility as I put new plates and springs in, I will have to see if anything changes when I get it fully on the road.

11
Recently replaced the clutch plates and springs on my 400 four and gave it a little test in the back garden and a knock that wasnt there has appeared and sounds like it is coming from the bottom of the engine. After some googling it seems like it might be a lose/worn primary chain. Other sugestions have been a carb issue but I got those sonic cleaned and set up with new kits in them and its running on all cylinders.

Give the video a listen and tell me if im gonna have to strip the engine down again. https://photos.google.com/share/AF1QipMzQce26RgLVLq-uJWXg-i-HhjCKujmF-t1_xEDfvQGV3FPlmYHzeP0bBw3Xdvj3g/photo/AF1QipOW_5baTlb13aNyf2tYgRtuygXFKvbL2p11n6ZE?key=cUZpRDVqQjk2SVF3cjZzMVpOVTlyZW5WYUZsUEt3

12
Desperately Seeking!! / CB 400 four f2 Clutch Adjuster bolt
« on: June 28, 2019, 06:59:20 PM »
I need a clutch adjuster bolt (22818-354-000) for my 400 four. Its the last thing before I can get it on the road but cant find one anywhere. Ive contacted 400fourbits but he doesnt have any. Does anyone have one spare, can link me to a seller who has them, or knows another similar bolt that works just as well. Much apreciated !!

13
CB350/400 / Re: Oil leak help and sense check.
« on: May 25, 2019, 10:27:35 PM »
In fact, the closer I look, it actually looks like that gasket was split when fitted, its not sitting right at all. 🤔 And, someone has been there with a flat blade it screwdriver by the looks of it 🤔🤔

Dont know how long the last owner had this gasket on but it ripped in quite a few places when  I took the barrels off. It does look like a flat head has been at it :D but it's just where its ripped

14
CB350/400 / Oil leak help and sense check.
« on: May 25, 2019, 04:55:19 PM »
So there is an oil leak coming from the bottom of the barrels around where the oil breather dowel is. After taking the barrels off the gasket is nackerd and seems to be split where the dowel is (pic 1 and 2) so I'm thinking that could be the reason for the leak.

Now for the sense check. After having a look at the CB400 four engine rebuild that Nurse Julie posted it seems like the little o-rings that go around the dowels werent there (pic 3). So it seems to be a combination of both the gasket and the o-ring. I plan on replacing the gasket, obviously, but couldnt find the little o-rings for the dowels on davidsilvers, unless I missed them. Could someone point me towards them? They definitely should have the o-rings for the dowels right? I couldnt find any mention of the o-rings in part diapgrams I've been looking at.

15
CB350/400 / Cb400 four silencers
« on: May 19, 2019, 06:43:32 PM »
Been looking for a new silencer for the CB400 four I've just bought. I have found the davidsilverspares one but was wondering if anyone is using a different brand or a different style of silencer.

Pages: [1] 2
SimplePortal 2.3.5 © 2008-2012, SimplePortal