Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bryanj

Pages: [1] 2 3 ... 413
1
CB350/400 / Re: Cb400f project #2
« on: Today at 09:58:38 AM »
I have posted a link on here somewhere to a very nice looking stainless repair kit BUT it all depends if the horseshoe is free. You may be able to check that if you remove cam cover but not always.
Just a top end is possible in frame so as long as horseshoe moves ok i would repair lockbolt, fit engine and try and get it running, fitting as little as possible

2
Desperately Seeking!! / Re: CB750 head socket
« on: Today at 09:53:42 AM »
Sorry dont see the point in spending that much when you have to completely remove top yoke to use it and its not necessary to use a torque wrench anyway

3
CB500/550 / Re: Oil and cylinder pressures
« on: June 06, 2020, 08:39:46 PM »
Both should be in manual but if light goes out oil is ok and you wont get full compression till after its been run and is warm

4
CB350/400 / Re: Cam chain tensioner bolt
« on: June 06, 2020, 08:38:04 PM »
It screws in till it clamps the tensioner rod

5
Misc / Open / Re: Photobucket
« on: June 06, 2020, 06:25:45 PM »
Julie, just make sure you have 2 of them used alternatley. The tears from a mates teenagers when the usb stick dies! And he develops software and sometimes can even repair memory sticks.

6
Recommended Sources for Parts and Services / Swing arm collar
« on: June 06, 2020, 09:33:49 AM »
I am working on a members 500 and found play in the swing arm.
As usual the collar was worn more than the bushes.
Normal hours spent removing bushes and bronze ones ordered from Julie.
Next problem new collar needed Silvers and CMS  both well over £80 delivered and Silver no stock.
Found Andy Ceepoc on ebay had stock and delivered from Germany in 3 days for £69.
I know Andy has a mixed rep on here but in this case i cant praise him enough.

7
Desperately Seeking!! / Re: CB750 head socket
« on: June 06, 2020, 08:33:01 AM »
I use a C spanner

8
CB500/550 / Re: CMNSL exhaust - should I be worried ?
« on: June 06, 2020, 07:01:02 AM »
DS & CMSNL work together and sell to each other

9
Desperately Seeking!! / Re: CB750 head socket
« on: June 05, 2020, 05:47:38 PM »
Just a standard 3/8 drive socket

10
CB350/400 / Re: Rectifier
« on: June 05, 2020, 04:36:29 PM »
Looking at the pictures for that item i would fit the 1200 volt one simply because it is finned to disipated heat and its only pennies dearer

11
CB500/550 / Re: Rear Wheel (Doh!!!)
« on: June 05, 2020, 08:14:36 AM »
I came accross this years ago and the complete wheel will fit but spacers have to be played with

12
Misc / Open / Re: Is Hondamans shop still open?
« on: June 05, 2020, 08:11:47 AM »
I used to use a diamond file on all Honda four points when sevicing and if not "flat" within a few strokes replace them.
If i had a regular customer i knew that all they would need is a light clean and regap

13
Well i just bought some

14
Worries me it is semi synthetic listed for a car so may have friction inhibiters that wont do clutch any good

15
Other Bikes / Re: 1972 CB350 Twin
« on: June 04, 2020, 10:47:35 AM »
Cranks probably are worth doing now due to short supply, maybe Alpha bearings?

Pages: [1] 2 3 ... 413
SimplePortal 2.3.5 © 2008-2012, SimplePortal