SOHC.co.uk Forums > CB500/550

Partially Restored 74 CB550

<< < (24/45) > >>

McCabe-Thiele (Ted):
I think Ken did not approve but I used a blob of Hondabond on top of the grub screw with a small stainless washer as a cap.

Oddjob:
Not my place to approve or anything Ted, just wasn't needed though IMO.

Get something like these Dave to secure the rod, I put them in a drill and rest a file on the point as it spins to reduce the tip down until it fits inside the groove in the rod, I'd go with 10mm, maybe M5. Depends on the size of the hole you end up with after drilling out the locking pin

https://www.ebay.co.uk/itm/313583380550?var=612402648480&hash=item490306a846:g:XvIAAOSwVORg1sj0&amdata=enc%3AAQAIAAAA8DGZkN3dMdU6oZ1%2FXUF2wYy4uDn8uTx5w%2FccUdFWpkkwYU3zk97NDpXUpjcjUhFYieAaa%2BoQ6Fa%2FWGYDQg0o253pEmtkSqE3%2FNc3mKmmjYKomemf%2FbRfJPdB%2B74BOMv9bzbXkEbA2sQygCsbvJcC04VGpAGamK0UW%2BpdI8nsU8HjL0Dxa%2BxYda9oLaCJYh61bru%2B3vkqR4zVDeq72nociFNF0kK%2B%2FNFu6zzoINGD4qf2gU2UQG1s25RFd%2FyNUbYNlJILctm%2FeZzvNF8zkbtfb9eXGMZn75aBbHYZQrp%2B1oPLFdh1pWNNgNPiej8rGa%2Bmlg%3D%3D%7Ctkp%3ABk9SR-SLqueAYw

McCabe-Thiele (Ted):

--- Quote from: Oddjob on November 25, 2023, 12:33:59 PM ---Not my place to approve or anything Ted, just wasn't needed though IMO.

--- End quote ---

OTT v OCD. 😁😁😁

davidcumbria:

--- Quote from: Oddjob on November 25, 2023, 12:33:59 PM ---Not my place to approve or anything Ted, just wasn't needed though IMO.

Get something like these Dave to secure the rod, I put them in a drill and rest a file on the point as it spins to reduce the tip down until it fits inside the groove in the rod, I'd go with 10mm, maybe M5. Depends on the size of the hole you end up with after drilling out the locking pin

https://www.ebay.co.uk/itm/313583380550?var=612402648480&hash=item490306a846:g:XvIAAOSwVORg1sj0&amdata=enc%3AAQAIAAAA8DGZkN3dMdU6oZ1%2FXUF2wYy4uDn8uTx5w%2FccUdFWpkkwYU3zk97NDpXUpjcjUhFYieAaa%2BoQ6Fa%2FWGYDQg0o253pEmtkSqE3%2FNc3mKmmjYKomemf%2FbRfJPdB%2B74BOMv9bzbXkEbA2sQygCsbvJcC04VGpAGamK0UW%2BpdI8nsU8HjL0Dxa%2BxYda9oLaCJYh61bru%2B3vkqR4zVDeq72nociFNF0kK%2B%2FNFu6zzoINGD4qf2gU2UQG1s25RFd%2FyNUbYNlJILctm%2FeZzvNF8zkbtfb9eXGMZn75aBbHYZQrp%2B1oPLFdh1pWNNgNPiej8rGa%2Bmlg%3D%3D%7Ctkp%3ABk9SR-SLqueAYw

--- End quote ---
Sure Ken that’s what’s I’m buying but my question is how to make sure it doesn’t unscrew itself with the motion of the shaft ?

Oddjob:
Use some thread lock if it worries you. So long as the tang is smaller than the slot, so not a tight fit it should be ok.

Navigation

[0] Message Index

[#] Next page

[*] Previous page