SOHC.co.uk Forums > Project Board
Honda CB400NA Superdream - new money puddle.
McCabe-Thiele (Ted):
After mixed results plus daft rising costs/quotations from two local firms I have used previously a mate put me in touch with a small firm near Chesterfield. They specialise in vehicle paintwork they also do powder coating.
As the Superdream is never going to have much end value I have taken a risk and taken the frame to them. I will report back on what sort of job they make of it and name the place when I have the frame back, hopefully by the end of next week.
Photos will be posted, I'm using the firm based on recommendation from someone whose opinion I value.
andy120t:
Ted - what are the plastic / polishing wheels you referred to?
Skoti:
Don't know what Ted used, but I got a similar result using a scotchbrite pad type version of a polishing disc from Lidl.
Not too brutal but enough to easily remove the lacquer and gently polish up alloy.
Then finished by hand with solvol autosol.
And finally done with autoglym super resin to seal the elements out.
EDIT.
Parkside fibre disc set, item number PWSZSP1.
Laverda Dave:
Details of the polishing discs are here:
Wobekuy 50Pcs 1 Inch Radial Bristle Disc Kit Abrasive Brush 3mm Shank Detail Polishing Wheel for Rotary Tool Accessories
https://amzn.eu/d/cETlHwP
Amazon are showing no stock at the moment :(
I notice Ken has previously posted a review on these and if they are good enough for Ken they were good enough for me. They are are great product.
McCabe-Thiele (Ted):
--- Quote from: andy120t on December 10, 2024, 06:26:40 AM ---Ted - what are the plastic / polishing wheels you referred to?
--- End quote ---
I use two of the polishing discs on the same shaft, although they come in a range of coarseness I tend to use the 220 grit equivalent ones for the first phase, then the 1000 grit. One pair of wheels lasts for ages as long as you do not apply too much pressure or have your dremel type tool set too fast. The plastic discs are directional, it takes a bit of practice as you need the wheels ideally to be at 90 deg to the metal. I used a cordless drill back in 2020, a dremel type tool is much better, mine is a mains powered Von Hous recommended by a member. Final phase is the buffing wheel using the different grades of finishing soap.
Ken has discovered a new super grade of finishing soap that he was telling me about last week - it's Gold and priced accordingly.
These are the ones Ken uses & recommends, I think they are mentioned in Tricks & Tips here http://www.sohc.co.uk/index.php/topic,28743.0.html
This is a link to Amazon item.https://www.amazon.co.uk/dp/B097NHP7CM?ref=ppx_yo2ov_dt_b_fed_asin_title
On e bay as well.https://www.ebay.co.uk/itm/394131453050?_skw=50Pcs+1+Inch+Radial+Bristle+Disc+Kit+Abrasive+Brush+3mm+Shank+Detail+Polishing+Wheel+for+Rotary+Tool+Accessories&itmmeta=01JEQWS4BY6TZM375PFW2BX040&hash=item5bc410b47a:g:wD0AAOSw-DZitWMN&itmprp=enc%3AAQAJAAABUHoV3kP08IDx%2BKZ9MfhVJKnp8dE1FFjQCgxVke0%2BzYARIvWPkdbXZ8lO%2Fivqt4fzhu88G12OSAqyMIBVsrO3xC0sKtH6rQiaA2oVEBbOd36AfzRXjw96vwxiSqDcv6b9AUlUfNZT4lmIDVJesLqF%2B7nQXxG2okuAG6WJ1w%2FfjmY6icjKFLS8MAVuA5qaKED5opbdh9C7Yrb%2BOrNcB9WMz4p82VSqwNVJkWW13QIAxyAC%2F77Gs8SNalSFWBSqqwd8Vuho1xvrzU16Sm9ZZhBj2zYFOj17uMdzWFsV852YIT%2FjhuFyE0eVVlj6FiISDyGw4o4baJYcQUAQTCstBA17q%2FNCe7F8iE4EaS2fB3A4Y7mw50%2Fg7iw4s14N74AidkJE%2FOIc2Ua17wjH68dOjA8bIXlCTos29GPb05GffQoujWj36jZ6kASXSwggQS2oeYuvmQ%3D%3D%7Ctkp%3ABFBMhMbk_PVk
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version