Author Topic: Oil filter housing O Ring keeps blowing out  (Read 1955 times)

Offline Oddjob

  • SOHC Jedi
  • Posts: 4827
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #30 on: November 11, 2026, 02:21:00 PM »
Just looking at the picture of your engine Johnny.

Just some words of advice learned through many years of owning one of these bikes. Fitting a socket bolt into the gear lever pinch bolt area doesn't work. They can't exert enough force to really clamp the lever to the shaft without them rounding out. The result is they either vibrate loose and fall out on a ride or the lever starts to slip, causing the splines on either the shaft or the lever or both to round off. Result, new lever or shaft or both. The other thing that happens is the the hole in the top fills with water, all those socket screws facing upwards will suffer from this. They may be stainless but they will rust, when you go to remove them some years later you find they round off before letting go, with the shape of those button head you have no grip for any mole grips etc. Drilling stainless is hard so drilling them out will be very difficult. If you don't like the standard JIS casing screws (and I don't) then fit some of the modern Honda 8mm headed bolts instead. They look better, perform better and are readily available at not a great cost. There is a detailed post on part numbers for these bolts on the site.


In the gear lever fit a stainless steel 20mm bolt there as fitted as standard. With a washer under the head or you'll mark the chrome tightening it up. Try Middletons for stainless steel bolts, they aren't marked on the head and come ready polished. Do the starter motor cover ones at the same time, get lengths from a parts book.

As I said, just some advise, you can ignore it if you wish.
Kids in a the back seat cause accidents.
Accidents in the back seat cause kids.

Offline Johny Boy

  • SOHC Associate
  • Posts: 53
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #31 on: November 11, 2026, 02:26:50 PM »
Thanks for that, I will take that on board, especially as I'm currently taking the engine out.

Thanks for the previous post showing the relief valve set up, mine was like this.
Also to answer an earlier post, the bypass is internal to the pump, when open it feeds oil back to the low pressure side, you can just about see the path on the attached photo. [ Guests cannot view attachments ]
CB550 (85% there)
New BSA Goldstar (my daily)
MV Agusta F4 750 Senna (Front room love affair)
BSA bantam (my constant pain in the arse)

Offline Bryanj

  • Grogu
  • *
  • Posts: 12636
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #32 on: November 11, 2026, 02:33:30 PM »
If it bypasses to the intake it cant be moving enough to allow bypass

Offline Ken4004

  • Semi retired hiding from wife in shed
  • SOHC Expert
  • Posts: 309
  • Triumph Tiger sport 2013. Honda CB 400 4
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #33 on: November 11, 2026, 03:24:34 PM »
Hi badger, yes they have been vapour blasted and they do look brand new, well worth the money if doing a full rebuild.

You raise a good point, I did give them an extra wash but now really wishing I had blasted some 6 bar air down every hole, which I can't guarantee I did.

If I can't find the issue with the relief valve, a full strip and clean might be necessary.
From what I read the relief valve should open about 60 psi, roughly 4 bar so I am going to investigate and then see if I can get it to move with some air pressure.

I had my cb400 4 engine vapour blasted, expensive but really looks like new when finished and in my opinion well worth it.
The guy who blasted mine never reused blast medium so the finish was totally uniform all over the engine.

While I was there he showed me a brass engine casing from an old car he had just finished and it looked like a piece of gold .
I did um and ah about the cost but thought just go for it and I wasn’t disappointed.

Offline McCabe-Thiele (Ted)

  • Grogu
  • *
  • Posts: 8739
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #34 on: November 11, 2026, 09:31:04 PM »
If it bypasses to the intake it cant be moving enough to allow bypass

The oil path will only be open to the intake when the valve is opened by the valve, due to  excess oil pressure.
« Last Edit: November 12, 2026, 09:24:21 AM by McCabe-Thiele (Ted) »
Honda CB400NA Superdream (current money puddle)
Honda CB500 K1 (second money pit)
https://www.sohc.co.uk/index.php/topic,28541.0.html
Honda CB400 four super sport (first money pit)
Link to my full restoration http://www.sohc.co.uk/index.php/topic,23291.0.html
This is a neat 500 restoration in the USA.
http://forums.sohc4.net/index.php/topic,151576.msg1731556.html#msg1731556

Offline scottly

  • Newbie
  • Posts: 33
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #35 on: November 12, 2026, 03:17:58 PM »

Old / wrong Spring fitted? It seems to fit and an old spring should get softer as it ages meaning lower relief pressure.

I ran across this on the US forum today. Might be worth a read?
https://forums.sohc4.net/index.php/topic,192531.msg2244067.html#msg2244067
Seeley SH7-521 owned since 1979

Offline Johny Boy

  • SOHC Associate
  • Posts: 53
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #36 on: November 12, 2026, 03:53:32 PM »

Old / wrong Spring fitted? It seems to fit and an old spring should get softer as it ages meaning lower relief pressure.

I ran across this on the US forum today. Might be worth a read?
https://forums.sohc4.net/index.php/topic,192531.msg2244067.html#msg2244067

That is interesting, I will measure mine up, after checking 550 / 750 share same spring.
I checked on David silver spares, they don't do it anymore but I think cmsnl do.
Will get a replacement as I'm doing a full strip down anyway
CB550 (85% there)
New BSA Goldstar (my daily)
MV Agusta F4 750 Senna (Front room love affair)
BSA bantam (my constant pain in the arse)

Offline Bryanj

  • Grogu
  • *
  • Posts: 12636
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #37 on: November 12, 2026, 09:06:11 PM »
Yes just checked at cms and both spring and plunger for 500 have 300 middle number so 750 parts

Offline scottly

  • Newbie
  • Posts: 33
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #38 on: November 13, 2026, 02:55:42 AM »


That is interesting, I will measure mine up, after checking 550 / 750 share same spring.
I checked on David silver spares, they don't do it anymore but I think cmsnl do.
Will get a replacement as I'm doing a full strip down anyway
Measure the spring before taking the whole motor apart. ;) Brent measured 17.21mm fully compressed with the aftermarket spring, compared to a stock spring at 15.88mm . He also noted the maximum fully compressed spring length for the relief valve to function was 16.45mm.
Seeley SH7-521 owned since 1979

Offline scottly

  • Newbie
  • Posts: 33
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #39 on: November 13, 2026, 03:53:19 AM »
Has there been any check of oil flow to the top end of the motor? Take a peek under the tappet covers and see if oil is getting to the cam.
Seeley SH7-521 owned since 1979

Offline Johny Boy

  • SOHC Associate
  • Posts: 53
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #40 on: November 16, 2026, 06:57:14 PM »
Hi everyone, so I've stripped her down.

Oil is getting around the whole engine.
I can't find any blocked oil ways.
Unfortunately there was vapour blasting debris in big oil passage mentioned by oddjob.
The remaining oil in there was pretty murky.
I can't see any damage to the camshaft or crankshaft journals.
There is however some damage to the main bearing shells (see picture)
This is the worse one by far, but it has not gone completely through the coating.

So my question is, would you rebuild with those shells.
My first thought was a big NO, but then assuming I get it all cleaned out there would be no more wear in the worn areas, o [ Guests cannot view attachments ] r is that a stupid idea?
CB550 (85% there)
New BSA Goldstar (my daily)
MV Agusta F4 750 Senna (Front room love affair)
BSA bantam (my constant pain in the arse)

Offline Nurse Julie

  • 1977 CB550/4 Mongrel Brat. 1974 UK 500/4 K1. Honda CD250u.
  • Grogu
  • *
  • Posts: 8758
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #41 on: November 16, 2026, 07:11:55 PM »
That's fooked.
LINK TO MY EBAY PAGE. As many of you know already, I give discount and do post at cost to forum members if you PM me direct.
https://www.ebay.co.uk/sch/julies9731/m.html?item=165142672569&rt=nc&_trksid=p2047675.m3561.l2562

LINK TO MY CB400/4 ENGINE STRIP / ASSESSMENT AND REBUILD...NOW COMPLETE
http://www.sohc.co.uk/index.php/topic,14049.msg112691/topicseen.html#new

Offline McCabe-Thiele (Ted)

  • Grogu
  • *
  • Posts: 8739
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #42 on: November 16, 2026, 07:46:40 PM »
For the cost of one pair of main bearings I would replace those.
Is that main bearing on the oil pump side of the engine casing?
Are you sure from your findings that you have found enough blocked passages to cause the oil filter O ring to blow out?
Honda CB400NA Superdream (current money puddle)
Honda CB500 K1 (second money pit)
https://www.sohc.co.uk/index.php/topic,28541.0.html
Honda CB400 four super sport (first money pit)
Link to my full restoration http://www.sohc.co.uk/index.php/topic,23291.0.html
This is a neat 500 restoration in the USA.
http://forums.sohc4.net/index.php/topic,151576.msg1731556.html#msg1731556

Offline Skoti

  • SOHC Pro
  • Posts: 622
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #43 on: November 16, 2026, 07:51:31 PM »
I have to agree with Julie's technical description.

Also may I suggest you be more sparing with the crankcase sealer when you re-assemble it next time.
I can see a big strip hanging off the edge of the case, that stuff also blocks oils ways and chokes oil pump strainer gauzes.

Good luck
Skoti


Motorcycling is Life, anything B4 or after is just waiting...

1976 Honda CB750F1

Offline McCabe-Thiele (Ted)

  • Grogu
  • *
  • Posts: 8739
    • View Profile
Re: Oil filter housing O Ring keeps blowing out
« Reply #44 on: November 16, 2026, 08:10:26 PM »
I used  bottle brushes of the correct size to clean the main oil galleries followed by a fresh wash with petrol as my casings were not vapour blasted.
I assume you will use an oil can and pump some oil through all the oil pathways you can find, including to the cylinder head.

Skoti raise a good point about ensuring that the sealant film is as thin as possible, I used Hondabond, I think NJ gave me a tip about wearing surgical gloves as they enable the thinest smear of sealant on the casing. So thin its almost transparent. I had plenty of practice as I had a few groundhog days when assembling my casings, primarily due to worn C rings.
Honda CB400NA Superdream (current money puddle)
Honda CB500 K1 (second money pit)
https://www.sohc.co.uk/index.php/topic,28541.0.html
Honda CB400 four super sport (first money pit)
Link to my full restoration http://www.sohc.co.uk/index.php/topic,23291.0.html
This is a neat 500 restoration in the USA.
http://forums.sohc4.net/index.php/topic,151576.msg1731556.html#msg1731556