SOHC.co.uk Forums > CB500/550

Well worth the money

<< < (4/5) > >>

Trigger:
All stickers are in place, even the Showa 323 on the shocks. Got the shocks from the states, came off a 9,000 mile bike with the original showa sticker still in perfect condition.You can always buy the pipes back but, they will come with the bike mate ;)

deltarider:

--- Quote ---and that means a mixture of the 500 and the 550
--- End quote ---
Could you give some details?

AshimotoK0:

--- Quote from: Trigger on June 18, 2015, 05:55:29 PM ---
--- Quote from: Oddjob on June 18, 2015, 01:02:48 PM ---Are those my old exhausts on there Graham?

--- End quote ---

No mate, the exhausts on the black one have been re-chromed. Yours are on the gold one.

--- End quote ---

What did you pay for re-chroming Graham and who did it?

Gorgeous looking bikes BTW

deltarider:

--- Quote ---what Honda used on the K2 version
--- End quote ---
It's amazing how many of the mods you described are standard on my 1976 CB500K2 (ED), which btw differs from the USA 500K2 (1973). Mine has the bigger clocks, the safety switch, 3 fuses and shares many things with the CB550K2 (1976) that was not exported to Europe. Here's a good vid of mine (not really mine, this is owned by an Italian, but I have the same). https://www.youtube.com/watch?v=Ux89PppUsxU
Stupid enough I left the grabrail (changed for a luggagerack) at my former address. So stupid, because that grabrail gave the bike that slick appearance. Mine has done 100.000 kms more than his but idles much nicer. Note that our Italian friend didn't fasten the front axle clamps the right way. Also I wouldn't rev it that high without load.
Mine is original except for the Koni's in the rear, forsaid luggage rack and a set of Voxbell horns that has a loud and distinctive sound.

deltarider:

--- Quote ---The top yoke isn't the same as the 500K1, more like the 550 as it uses the smaller fork clamp bolts.
--- End quote ---
Well spotted (as captain Mainwaring would say). The 7mm clamp bolts (instead of the 8mm) is one of the things shared with the CB550K2. No need for these D shaped washers anymore. The center grease niple (that I hate btw) is another thing.

--- Quote ---Why you'd fit a 18" front wheel is beyond me but I suppose it might handle ok.
--- End quote ---

I didn't, he, the Italian did.

--- Quote ---Never knew the K2 had the throttle cruise control arrangement, looks like 550 switchgear as well.
--- End quote ---
Correct but I doubt it was ment as a cruise control.


--- Quote ---One thing I forgot to mention looking at the vid was the chain guard, I always hated that big old black plastic chainguard on the 500 so I adapted the chrome 550 one to fit, not that hard really, just a new hole and tap the new thread.
--- End quote ---
Ah, you like shiny things. Me? Mwah. See below.


--- Quote ---Surprised they kept the fork gaiters as the bike looks better without them, like the 550F, ok they serve a very useful function but they look dowdy and they do tend to mask you've blown a fork seal for a long while. All in all I prefer the naked look of the 550F but that's just me
--- End quote ---
.
I disagree here with you. I'm not particular fond of shiny parts but prefer the classic look of these wonderful gaiters. How many can say that with 134.000 kms they have not changed one forkseal yet. Thanks to them gaiters.

Navigation

[0] Message Index

[#] Next page

[*] Previous page