Honda-SOHC

SOHC.co.uk Forums => CB350/400 => Topic started by: stevush on May 04, 2017, 04:36:33 PM

Title: Clutch Switch wiring
Post by: stevush on May 04, 2017, 04:36:33 PM
Can anyone help me with Clutch switch wiring please ? The old knackered switch has two wires Green and Green/Red which I assume connect to the same colour wires in the headlamp. The new aftermarket  switch has Black and Green/Yellow, can anyone tell me what goes to what in the headlamp please?

Thanks
regards
Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 04:55:43 PM
It doesn't matter, it's only a switch.  Just connect it to the G and G/R in the headlamp shell.
Title: Re: Clutch Switch wiring
Post by: stevush on May 04, 2017, 05:10:54 PM
Well maybe I have a problem elsewhere. The neutral light works fine, on in neutral, off in gear. When I connect the switch the neutral light is on permanently, whether its in gear or not.

Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 05:18:37 PM
Check the diode.  It should only conduct in one direction.   If you havent got a multimeter, a battery and bulb will suffice.
Title: Re: Clutch Switch wiring
Post by: stevush on May 04, 2017, 05:23:10 PM
Where's the diode ???

Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 05:27:28 PM
Its a small rectangular black plastic thing about half an inch big. (Don't correct me on the size, I'm not going to measure it)*
It's under the LH sidepanel and it just pulls out.


* there's some picky sods on this forum.   ;D
Title: Re: Clutch Switch wiring
Post by: Nurse Julie on May 04, 2017, 05:50:03 PM

* there's some picky sods on this forum.   ;D

 ;D ;D ;D ;D  ;D Who would that be then Mike ?
Title: Re: Clutch Switch wiring
Post by: stevush on May 04, 2017, 05:56:15 PM
Found it.. I have a couple of spares too. When the meter is switched to Diode test mode its also continuity ?
It beeps for continuity in both directions on all the diodes I have ?

I'm confused  :)

Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 06:09:48 PM
I never use the diode test function; I use the low ohm setting.  I think a battery and bulb gives a more reliable test.
Title: Re: Clutch Switch wiring
Post by: stevush on May 04, 2017, 06:26:35 PM
Testing with a bulb and a battery, the bulb lights both ways, all the diodes I have read the same. Does that mean they're all duff ?

Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 06:34:41 PM
Correct,  they're short.  All the diode does is to allow the starter motor when in gear provided the clutch is in.  It's ok to leave it out - it's just more inconvenient.
Title: Re: Clutch Switch wiring
Post by: stevush on May 04, 2017, 06:40:17 PM
OK Mike Thankyou, looking at DS, they're £25 and out of stock so maybe I'll leave it out.

Thanks
Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 07:03:07 PM
I'll have a look in my pile onthe weekend.
Title: Re: Clutch Switch wiring
Post by: stevush on May 04, 2017, 07:04:14 PM
Great stuff, thanks

Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 04, 2017, 09:16:32 PM
I've studied the circuit and ran some simulations.  If no diode is available there are two alternatives;

*  Leave the diode out
    This means it will only start when the clutch is pulled in, even when in neutral.

*  Short the diode out.
    It will work as normal except pulling the clutch in makes the neutral light come on

This is the best option
   
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 06, 2017, 06:22:13 PM
I had a good rummage for a diode but didn't find one.
Title: Re: Clutch Switch wiring
Post by: stevush on May 07, 2017, 09:52:53 AM
OK Mike, thanks for looking. Anyone else got one ?

Regards
Steve
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 07, 2017, 10:56:13 AM
Erwin83 may have one, he's getting rid of 400four bits.
Title: Re: Clutch Switch wiring
Post by: BigAl (Alan) on May 07, 2017, 11:04:03 AM
Hi Steve,

I have one for sale (used item) £10.00 free p/p.  Please PM your details

They are tested (as image) this morning

Alan
Title: Re: Clutch Switch wiring
Post by: mike the bike on May 07, 2017, 11:32:20 AM
Good old Avo 8 Mk5 I see
Title: Re: Clutch Switch wiring
Post by: stevush on May 07, 2017, 11:55:31 AM
Thanks for the Diode Alan, you have a PM. I took the diode out altogether.
I've ordered a new genuine clutch switch from DS this morning, the (new) one that I got last week fell apart in my hands before I even got a chance to fit it. That's the second (new) one I've had that was rubbish so I'm hoping 3rd time lucky.

Went to start the bike this morning with diode and clutch switch out and nothing at the starter button in neutral.....
Put diode back in, power to the button and it started straight up.
I'm hopefully on the last lap now, I'll post pictures when finished. I just need carbs setting up, an engine tune and (hopefully) an MOT.
Roll on Sunmmer  :)

Regards
Steve
Title: Re: Clutch Switch wiring
Post by: BigAl (Alan) on May 07, 2017, 12:21:53 PM
Steve, I have replied to your PM

Mike, Indeed it is, AVO model 8 Mark 5, bulky, but excellent accuracy.