Honda-SOHC

SOHC.co.uk Forums => CB500/550 => Topic started by: MIKE550/4 on September 07, 2009, 10:31:52 AM

Title: need a seal part no
Post by: MIKE550/4 on September 07, 2009, 10:31:52 AM

difficult to pin this down in words,

 steve d  you dont happen to have parts list photo for the front spindle do you ,

 best i can explain is where the chrome cover sits speedo side , under that chrome cover there is part which splits into 2, round the part that pushes out is a rubber seal, it looks like a ver small rubber band

550 k3

cheers if you can help

Title: Re: need a seal part no
Post by: MIKE550/4 on September 07, 2009, 10:56:48 AM

nearest pic i could find , part 8, the middle section pushes out and there is a seal round the part that comes out, only gives part no for whole item, only need the seal ... anyone ?


http://www.motogrid.com/pages/parts/viewbybrand/parts.aspx

Title: Re: need a seal part no
Post by: matthewmosse on September 07, 2009, 11:31:04 AM

Silvers can normally find these bits over the phone without part numbers, might do the trick. Ps did you get the bearing retainer out in the end?

Title: Re: need a seal part no
Post by: SteveD CB500K0 on September 07, 2009, 12:13:04 PM

Don't know if this helps, but...

Title: Re: need a seal part no
Post by: MIKE550/4 on September 07, 2009, 12:15:14 PM

Yes its all stipped , have one side of bearing back in , had to chop it out in the end , still  got to do back wheel ,  big learning curve for me this but getting there

Title: Re: need a seal part no
Post by: MIKE550/4 on September 07, 2009, 12:21:47 PM

will see if its available seperately cheers

Title: Re: need a seal part no
Post by: MIKE550/4 on September 07, 2009, 12:58:15 PM

Well not available from ds, might have to make something

Title: Re: need a seal part no
Post by: Bryanj on September 07, 2009, 05:04:39 PM

The only seal I know of is part of the speedo drive.

Title: Re: need a seal part no
Post by: MIKE550/4 on September 07, 2009, 09:34:33 PM

bryan on that part no  8 there is a section that pushes out, round that part there is like a band will try and get a pic up

Title: Re: need a seal part no
Post by: MIKE550/4 on September 08, 2009, 10:24:10 AM

can i get away with re using or adapt something else

(http://i156.photobucket.com/albums/t6/mike070868/july28-1.jpg)

Title: Re: need a seal part no
Post by: SteveD CB500K0 on September 08, 2009, 10:58:34 AM

I don't see why not - there's no oil pressure behind it is there?

Title: Re: need a seal part no
Post by: MIKE550/4 on September 08, 2009, 12:03:11 PM

that i am unsure of

Title: Re: need a seal part no
Post by: SteveD CB500K0 on September 08, 2009, 01:34:03 PM

That was a rhetorical question Mike...    ;D

There is no pressure - it's just a grease seal for the front wheel.

Title: Re: need a seal part no
Post by: MIKE550/4 on September 08, 2009, 01:39:07 PM

 :D
Oh right steve, will make something to get this sealed up , just got back to change bearings and then wheels can go back on

getting there slowly

Title: Re: need a seal part no
Post by: Bryanj on September 09, 2009, 07:02:21 AM

That speedo drive plate is totaly different to ANYTHING i have seen before!! It ought to be one steel piece or how will it drive the gearbox?