Honda-SOHC
SOHC.co.uk Forums => CB500/550 => Topic started by: mhirst121 on January 24, 2010, 05:04:56 PM
-
Well I thought you all might like to see some pics of my progress so far. The bike was an ebay buy and alot rougher than I first thought once stripped down. The bike has been completely rebuilt and painted, apart from the motor which was ok. The first pics are as I bought it in its horrible burgundy guise. The tank and panels have been done in basecoat and orange metal flake(blast from the past !!!). I don`t like the stripes I have put on the tank so have some originals coming and will redo the entire tank again when the weather picks up a bit. Hope you enjoy and will post some better ones in the daylight. Up till now I have spent about 2 1/2 months on the resto.
Cheers,
MartinH
(http://i28.photobucket.com/albums/c242/snaky121/honda6.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/honda4.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/honda2.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/IMG_0589.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/IMG_0594.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/IMG_0593.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/IMG_0592.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/IMG_0591.jpg)
(http://i28.photobucket.com/albums/c242/snaky121/IMG_0590.jpg)
-
Looks great! 8) 8)
-
Anyone know an easy way to get the main stand spring on!!! >:( >:(
-
This is how i have done it before on my 750, start with stand, spring etc off the bike, attach the c shaped plate to the lug on the frame & attach the spring to it, then attach the the other end of the spring to the centre stand, now you should be able to hold on to the stand and pull on it to line the holes up with the frame for the stand spindle and push it into place ;) job done just tighten everything up :) cheers Mick
-
Thanks Mick will give that a go.
-
This may be an urban myth but...
Open up each "link" of the spring with a flat bladed screwdriver and insert a penny. slip the "extended" spring over both retainers and then remove pennies with a pair of pliers. ;D
I think this came from .net but I don't remember who...
-
Well Steve I am impressed. The spring thing worked a treat, only I used washers not rich enough to use pennies(spent all of them on my bike ;))
Cheers,
MartinH
-
Amother one with new life breathed into it, sure looks good.
Cheers
Den
-
Yes that does look real good well done you must be well proud
Pete
-
Really nice job that. I always liked the 500. Are the exhausts available now?
-
Yes, you can buy individual or full sets from David Silver.
-
As Steve said, yes the exhausts and brackets are available from Silvers. They were an absolute pig to fit, the two small link pipes are too short in my oppinion and they are out of alignment. Just had to make the best of a bad job by modding the brackets and fiddling around.
Has anyone else had this problem????
MartinH
-
Yup, the brackets are pattern so probably not quite right, allong with 40 year old exhaust assembly jigs
-
Where are you getting the tank stripes from. I've bought a set from Dave Silver but am not impressed and could do with a better set.
-
Those are the ones I have. I was as unimpressed as you, but it seems thats the best available, without getting them specially cut. Are the lines on yours all shapes, as if they were done freehand??
KnK in the states do some but they look like they are the same thing.
http://www.knkcycles.com/hondaCB500.html
MartinH
-
These may be worth a look
http://www.sunrisegraphics.co.uk/
Seamus
-
Seamus, I emailed them twice and still waiting for a reply. Suggest if anyone wants to contact them they try the phone, I tried this once and no answer !!! ::)
MartinH
-
I must confess that I dealt with them at a bike show, so was easy.
They do have a good range of stuff though. May be worth the perseverance
Cheers
Seamus
-
The pinstripes aren't uniform and you have to trim the clear excess at the sides. I believe reproductiondecals.com sell the stripes. They can't advertise Honda decals but if you email them they they can provide them. I have emailed but not received a reply yet.
-
reproductiondecals got back in touch $55 including p&p to UK, is the same pinstripe sold by KnK for $80 including p&p. will ring Sunrise tomorrow but if cant get through I'll try reproductiondecals.
-
Sunrise seem to be a bit hard to get hold of, but the quality is reputedly good......
No personal expirience cos I don't do pretty bikes
-
Looks amazing, puts mine to shame.
What did you do with the old exhaust pipe?
The downtubes are a bit rotten and my bike sounds like a tractor at the moment, which I don't mind too much but I have an MOT test coming up soon so need to get it mended. If you want to sell it I may be interested at the right price.
-
Sunrise answered me email today,
-
Florence, have pm`d you about exhaust.
MartinH