Honda-SOHC
SOHC.co.uk Forums => CB350/400 => Topic started by: Ariel-KH-500 on May 07, 2026, 09:03:24 AM
-
Having problems starting the bike when its stood for a few days. When trying the start the bike I turn on the fuel about 5-10 minutes before trying it turns over ok and for about 4 presses of the button it makes no attempt to fire, after more presses of the button it fires once this then happens a few more times until it starts to run but very lumpy eventually it will chime up on all four cylinders and run. When ridden it performs as it should and when left for a few hours it stars as it should. So the jobs that I have done so far are Timing checked, valve clearances checked, balanced carbs, fitted new battery, checked petrol tank fuel filter, also only E5 fuel been used. I've now removed the carbs and have stripped them ready to ultrasonic clean them upon initial inspection they look spotless. The bike has only done 13,000 miles from new, I will post again in a few days to let you know if the cleaning was a success but in the meantime any ideas or advice gratefully received . PS bike stored in my dining room during the winter after draining the tank and putting fuel solutions storage fuel in it and running it through the carbs bike started ok after winter lay up.
-
My 400 was the same when I first had it running after 10 years of being in POs garage.
Turned out to be low compressions, all were even but not enough.
Try the Easystart spray test on the air box.
-
First off why turn the fuel on so early and leave for so long? It could be the problem or part of the problem. There should be enough in the float bowls to start the engine, unless you’re one of those that turn the tap off a few minutes from home and run the bowls dry, not knocking that practice but would go so way to explain the tap turning on thing. If the float levels are wrong it will start to flood the cylinders, that could mean it fails to start or it runs lumpy for a while until it’s burned it off.
How are the plugs looking? Are they new? Odd question but what make are they? Reason for that is there are a lot of fake NGK plugs around and a mate of mine had a similar problem on his Harley. He kept saying the plugs are new it’s not them. I kept telling him to refit the old ones and see if it was ok or the same but he was stubborn and stuck with his new ones. Of course they turned out to be fake, bought from a motorcycle shop btw not eBay. A month with no bike just because he thought new meant they couldn’t be the problem.
I’d really check the idle jets when you remove them, hold them up to a strong light and see if they are blocked.
Report after that or when others ask questions.
-
It dose not make any difference if I just turn the fuel on or turn it on early the problem is still the same, its probably an old habit riding my old classic bikes as if they have stood for a few days the old Amal carbs tend to evaporate.. spark plugs are new and purchased from David silver along with air filter and oil filter. Just waiting for cleaning fluid to arrive will post results when carbs have been cleaned refitted and balanced
-
If float valves (controlling fill from tank) are a OK, then it shouldn't matter how long the tap is left on prior to start.
As most things are checked, and carbs cleaned too, then if it persists a check of compression psi would be helpful in establishing whether anything is out of range there.
-
The point I was trying to make Nige was that IF the float needles were leaking or the float height was incorrect then that 5 min wait could be making things much worse or even be the source of the problem.
-
Yes agree with your thoughts Ken, it should show with wet feet though :) out through the overflow tubes, if they are letting by.
Interesting to hear if there's any improvement after the checks done and work on carbs.
-
When I posted regarding my starting issues I said that I would report back so here goes. Carbs taken off bike completely striped the carb bodies have been ultrasonic cleaned along with all the jets. The carbs then reassembled new O rings and slides set up on the bench, then refitted to the bike and all set up with vacuum gauges, bike started ok and ran fine, after leaving it for a few days went to start it and just like before turned over 2/3 times then fired but didn't start after a few more attempts it fired but rather lumpy the chiming in on all 4 once running it runs fine. I'm at a loss to think why as if I try to start it after a few hours it will start fine its only when it has not been started for a few day any ideas Kevin
-
Just my thoughts,
A retarded engine can be slow to start, is the timing correct for both 1/4 & 2/3?
Check no air leaks between engine & carbs.
Do you know the compression readings?
-
A couple of things to try in helping analysis and find out effect.
1) spray E-Z-start into airbox prior to cranking and see if there's any change to how it initially fires when cold.
2) cover airbox entry (thick rag or similar) and crank with kill switch off, just for a few 5 second bursts, then remove rag, switch on and try to start. Again, to observe if there's any immediate change in willingness to fire when cold etc.
-
Easy Start----- YEUK!!-- The work of the devil. The knocking noises I've heard over the years from enthusiastic use.
-
Easy Start----- YEUK!!-- The work of the devil. The knocking noises I've heard over the years from enthusiastic use.
Especially on a Diesel Engine.👍
-
I'm making some basic assumptions such as full choke with no throttle on cold start.
-
Easy Start----- YEUK!!-- The work of the devil. The knocking noises I've heard over the years from enthusiastic use.
Its just basic testing to gauge effect. What it can do is show there's impaired or low flow from idle fuel circuit that's supposed to be supplying at this juncture.
Improvement with "assistance" would indicate that the idle jet circuit needs further inspection ...... which no-one wants to do on these :)
The covered airbox test too, if there's notable improvement then again it suggests that the increase in inlet vacuum is more effective in pulling fuel up through the jets, initially.
-
Many seem to have difficulties with these 350's.... I've had my own share of grief with getting these carbs bench sync'd then set properly on the bike.... by chance has anyone decided to go up a size on the idle jets? And of course, did it help or hinder?
-
Many seem to have difficulties with these 350's.... I've had my own share of grief with getting these carbs bench sync'd then set properly on the bike.... by chance has anyone decided to go up a size on the idle jets? And of course, did it help or hinder?
A good question, and worthwhile considering as to ultimate aim of improvement.
Would that be to give larger bore in jet in trying to mitigate blocking ? Or something else.
I'd caveat my view with not wanting to run fuel excessively as there's downside in lubrication, bore washing etc from unburnt fuel going somewhere its not wanted. I'd be keen to observe care in that regard.
The flip side though, and built into strategy of injection system (along with exhaust monitoring in closed loop) is that a flexible approach could be worth consideration into further evaluation.
One size up for idle jet should bring a need to individually assess the air screw set point in utilising that flow, along with understanding what, if any, the gain will be.
Judging by setting that air to fuel ratio dynamically, as the manual instructs, will show how far you need to to move it in bringing the mixture in range. This is echoed in fuel injection strategy with long & short term trim values from running experience within the environment the vehicle is used. This effectively reinforces the method of rejetting and then judgment as well established theory and practice.
It may end up with broadly similar fuel flow, but facilitate cold start by enhancing choke effect against cranking vacuum by pulling initially more fuel through the slightly larger jet to get the combustion lit up in that first fire phase.
-
Another update on the 400 starting issues. After reading the suggestion of blocking off the air intake and turning over with the kill switch turned to the off position I tried this after not starting the bike for four days as the problem has always been when its been left a while, so fuel on kill switch off air box intake covered three four second bursts on the starter and low and behold it fired straight up. So according to previous post this indicates primary circuit I will now remove the carbs and investigate in the meantime anyone with previous experience of this problem or inspecting the primary circuit I would be very grateful for any advice thanks in advance.
-
I found this link is handy when taking the carbs apart - the photos are pretty good at illustrating how things go back together.
.https://www.vintagebikebuilder.com/cb350-400f-carb-rebuild-demonstration.html
I use DP60 or WD40 to check the airways in the body are clear, spray in at one end until it emerges at the other end of the carb body etc.
-
Or use a syringe and white spirit to verify that the internal passageways are clear.
While you have things apart , verify that the choke flaps are fully closing.
Regards
Dave
-
FWIW, my 400 has always been a hesitant cold starter from dead cold- with outside temps say below 10C/50F. My method nowadays is to turn the kill switch to the off position, put the choke fully on and spin the starter for 2-3 seconds. Then turn the kill switch on, hit start button. Bike starts immediately and choke lever is moved down a bit to maintain a fast idle - 1500 RPM or thereabouts. Choke can be off completely a minutes after start. In warmer weather it will start immediately from cold with the choke on - no need for "pre-spinning." It always needs the choke to start from cold, regardless of ambient temps.
In cold temps if I DON"T pre spin, just put the choke on, it typically takes at least 4-5 start attempts (each one a 2-3 second push of start button) before it will start/keep running.
I've always assumed it's just a cold blooded little sucker!
-
Hi Aerial
Have you resolved your cold start issue or is it still under investigation ?
Regards Ken
-
I removed the carbs yesterday and put them through the ultrasonic cleaner again at 60 degrees and for a 20 minutes , replaced the carbs and bike started ok I then rebalanced the carbs using my vacuum gauges. Bike start fine and ran ok on the bench. today I will start the bike again to see if all is cured although the real problem was when it had stood for a few days if it stars o k today I'm then going to leave it for a few days and see if it will start as it should. One question for the experts is there anywhere where I can get some new felt seals for the slide lifting spindles. will repost in a few days with an update.
-
Hi Aerial
When you took the carbs off the bike and open them up did you notice anything in the bowls like jelly ? , just wondering if the ethanol in the fuel has reacted with any moisture and this is clogging your pilot jets.
I had this once where I filled up with fuel at Sainsbury’s and within a mile of riding from the station the bike stopped and fuel was pouring out of all four carb over flows .
I removed the carbs to clean them and found lots of this jelly substance .
It would be nice to see something blocking the jets when you have taken the trouble to remove the cards from the bike !
-
No the float bowls were spotless inside,I always use e5 petrol (Esso) in all my bikes always from the same garage. After re fitting the carbs it started fine then left it for 24 hours and again started fine I am now going to leave it for 4/5 days and then see if it starts ok, the problem has always been when the bike has not been started for while if started every day no problems. I will post again next week with the result after it has stood un started.
-
An update on the starting issues, after the 2nd ultrasonic clean and carb balance the bike started 1st press of the starter it was then left over night and again a 1st press start. the bike was the left untouched for 4 days again 1st press start it was left again for 5 days and again started right up I've been out on it yesterday and did approx 80 miles with a stop at around half distance. I am now going to let the bike stand for a week and see if it still starts ok after not being started as this was always the main problem so far so good will report again when I next start the bike.
-
Good prospect of a positive conclusion it looks.
These pilot jets are so small though, and easily impaired even if a % of flow is compromised, they'll give this type of effect.
Often it's the jets (well, mostly in reality) as impaired flow matched against the expected vacuum during cranking just doesn't yeald enough to bring easy starting combustion mixture. The "blocking" airbox method obviously increases vacuum while cranking, which gives more confirmation in diagnosis. That will also pull through main jet if the slides (and needles) are lifted a little too.
It's possible though, with high ambient temperature, that it just may need slightly more of a spin after sitting for a week due to some evaporative effects in float bowls if the fuel is left in those. It's the "nice" volatile aromatic part of petrol that gets out to atmosphere first, via float bowl breather tubes and also the component in fuel that gives the combustion light off it's potency to get going.
Full choke to initially try is likely most successful, even in this weather.
As we see across various thread on here, these idle jet plus their circuit are absolutely key in having these carburettor run to their potential. Also a big part in running without flat spots and other associated ailments experienced.
-
One of the BIG items that folks like K2 and others helped me with when I was sorting out my setup is the fact that the "idle" circuit affects a much wider range on these engines/carbs than other bikes I have owned/worked on.
As noted, it is vital that the slow jets/air adjustment screw are working perfectly. When they are, the engine is responsive at any RPM. I can roll the throttle on to full from 1500RPM in 3rd gear and the bike will just pull away with no complaint, no lugging, just smoothly accelerate. Admittedly it not going to do any head snapping at that RPM but it's smooth and comfortable. Frankly, it can do it much better than my '21 Moto Guzzi V7 850 which, in stock form, was quite recalcitrant below 3000 RPM. The Honda is a much more comfortable bike trundling through small villages/hamlets at the 20MPH limit than the Guzzi was when stock.