Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - billdn

Pages: [1] 2 3 ... 22
1
CB350/400 / Re: Starter not disengaging
« on: March 26, 2026, 01:30:49 PM »
Thanks gents. Perfectly clear, good job I have spare solenoid.
Cheers

2
CB350/400 / Re: Starter not disengaging
« on: March 22, 2026, 12:29:43 PM »
Sounds like either the starter button or the starter solenoid isn't releasing.  If you have a bulb and some crock clips, you could disconnect the thick wire on the solenoid that runs to the starter motor, connect the bulb between the now free connector on the solenoid and chassis, and press away on the button.  Worse that could happen is the bulb stays on.

Does the starter button have a good spring back once released or is it gummed up by all the grease/oil from the throttle cable that has accumulated together with loads of crud.

The clutch on the starter shaft could be sticking and the motor is being spun by the engine but things would have to be pretty gummed up for that to happen.  From what you described sounds like the starter is free running once the engine speed picks up (faster than the starter)and the clutch disengages.

Regards
Dave

Sorry Dave, having dumb moment.  Are you saying test light should come on or should NOT come on.
Cheers
Bill
 

3
CB350/400 / Starter not disengaging
« on: March 15, 2026, 04:10:51 PM »
Having balanced the carbs  again! Yes, still fighting with running! Thought I'd got it about right . So disconnected carb balance kit, and buttoned everything up again I thought I'd fire it up again.  Started ok but with a dreadful screeching from the starter motor. Killed ignition but kept screeching,  so but of quick thinking and disconnected battery and screeching stopped. Turned ignition back on but not starting it and no repeat of noise. Before I remove starter motor I thought I'd consult you guys. Anyone had this happen. Electric starter had been intermittent but I presume was dirty switch,  kick start works fine. Loathe to start it again in case I do more damage. Over to you !

4
CB350/400 / Re: Any experience with vans to carry two Motos?
« on: September 14, 2023, 02:32:44 PM »
Someone I know hires a van one way to Liverpool with bikes on board, unloads at Liverpool,  rides to ferry and does reverse on return . Not sure if any cheaper though !

5
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 07:12:28 PM »
If you want another "pair of eyes" to help out with it Bill, I could have a day walkabout to see if we can get our heads around it together.

Which area are you located in West Sussex ?

Offer on the table should you need it.
Cheers gave sent you PM 👍

6
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 07:10:53 PM »
No don't have one, probably could borrow one. The engine has  been rebuilt from bottom up, rebore, new pistons,  rings, timing chain, primary chain, valves etc surely shouldn't  be compression problem.
You've far more experience than me so not saying your wrong, if so what's caused/causing it?
Before I switched to the Boyer I did get a good balance onbtge carbs but still wouldn't shut down when approaching giveaways etc.
Took them off, bench sync again , refitted added Boyer and now still same problem. Driving me 🤪. 

7
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 03:53:00 PM »
Just tried again,  wound #1 slider out a bit. Started but #1 bar doesn't even show on scale ,#2 rises a bit as adjusting the others. #3 bar shot to the top and #2 pipe popped off again with a distinctive pop sound but doesn't sound like a backfire. 3 and 4 nearly achieve adjustment but 2 and 1 not having it.

8
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 03:17:02 PM »
Very sorry to hear about the wife.

You could try this as to me it sounds as though the throttle lifters are set too high, especially if the carbs have been apart.

Get the adjuster screws, the ones with the little 8mm headed nuts on and the flat bladed screwdriver slot. Screw them all down as far as they can go. You may now struggle to get the bike to tickover and starting will involve a little jiggling with the throttle. Once you get it started adjust the main tickover screw to see if it will idle. If so, now vac the carbs to equalise them.

See if that works.

Before you do that post a pic of the adjusters so we can see how high they are now.

Hi Oddjob,
Just tried above and got it sort of running with enough revs to attempt Carbtune. Oddly #2 tube to carbtune kept blowing off the adaptor.  It was helping and adjustment could be made but soon as pipe blew off engine stalled.
Looks like a bench sync coming up 😏. Also#1 exhaust pipe was nowhere near as hot as the other three, although still hot to a degree. And yes did check carbtune pipes were on correct carb 🤣

9
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 02:30:30 PM »
Thanks Ted but all of the above is correct,  original brass and kept circlip in correct position.  Hope by end of day will have tried screwing down slides and vac gauge 🤞

10
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 11:30:39 AM »
I will go back and check my 350F build thread when I get a chance. My carbs came ready built from Gerben in Holland and came with the quadrant problem. He sent me an email of how to rectify it so will look for that as well. Yes the quadrant is where the push and pull cables connect. Is your pull cable only just fitting or is there plenty of adjustment.

Sent from my Pixel 7 Pro using Tapatalk
Cables fine Roy, plenty of adjustment on both, which I think is good 😏

11
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 11:27:22 AM »
Very sorry to hear about the wife.

You could try this as to me it sounds as though the throttle lifters are set too high, especially if the carbs have been apart.

Get the adjuster screws, the ones with the little 8mm headed nuts on and the flat bladed screwdriver slot. Screw them all down as far as they can go. You may now struggle to get the bike to tickover and starting will involve a little jiggling with the throttle. Once you get it started adjust the main tickover screw to see if it will idle. If so, now vac the carbs to equalise them.

See if that works.

Before you do that post a pic of the adjusters so we can see how high they are now.

Pics of adjusters prior too screwing in , hopefully attached

12
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 10:15:10 AM »
Thanks all for the thoughts and support, it's been a rough road .
but inwards and onwards!
I'll try Ken's suggestion first and then if needs be, and fear it will , I'll take off the carbs, again and do yet another bench sync. The guy on the production line building the 400 must have loved his job of fitting the carbs !
Might be a day or two as got to help the oldies (parents) for a few days after today.
But as Arnie says "I'll be back"

13
CB350/400 / Re: Still carb troubles
« on: September 05, 2023, 09:41:08 AM »
Sorry for your loss Bill.

That sounds to me like the quadrant is not positioned correctly when it was reassembled. Got the tee shirt for that one, took me ages to find it but the symptoms were as described above. Repositioned things correctly and it was spot on. Unfortunately the old memory won't allow me to remember how I fixed it but someone will know.

Sent from my Pixel 7 Pro using Tapatalk

Thanks Roy,
Not sure what you mean by the quadrant ? Do you mean the part the the push/pull throttle cables connect to? not sure how that could be misaligned but every day is a school day with this.
Cheers
Bill

14
CB350/400 / Still carb troubles
« on: September 04, 2023, 06:15:31 PM »
Back in February I posted saying I think I'd sorted my troubles with carbs not shutting down . In April I went for a Boyer electronic ignition complete with micro coils and I still have the same problem with the carbs !
There's quite a long time between posts because my wife was very ill with lung cancer and sadly passed on 30th June , so shed time was the last thing on my mind!
However one of her last wishes was "Get that bl##dy bike sorted!"  So I'm now back in the mood to try and sort it.

From the top :-
Boyer fitted and bike starts/runs. Using a timing light its correct.
Tappets adjusted.
Have to fiddle with idle adjuster to set at 1200rpm .
Idle mixture screw set at 2 turns out.
Plugs very sooty
Open throttle and revs soar and doesn't drop back to 1200rpm when released. Have to fiddle with idle adjuster to bring back down.
Sprayed carb manifold connectors to barrels with Carb cleaner and no effect , so not drawing in air, better not they're new - good
Remove carb tops and sprayed carb cleaner in but slides don't appear to be sticking either.
I've noticed that if you press the top of brass hexagonal nut on the carbs this will reduce the revs but too hard and it stalls FWIW.
Prior all carbs stripped, ultrasonic cleaned, carb cleaner on jets with jet brushes etc etc retaining original brass and new seals from NJ.
Bench synced at least twice.
Standard air box and new air filter

I've no idea what to do next! I have an old lawn mower, never serviced, starts first time every spring,  think I'll put engine from that in instead.

To me it's pretty obviously  carb related, (I think  ::)) as there is good spark and timing is ok. Not got to the stage with setting Boyer to full advance  yet which requires 4500rpm as revs all over the place.
Cheers peeps! 8)

15
CB350/400 / Re: Front disc brake adjustment
« on: June 09, 2023, 07:51:58 PM »
Thanks Oddjob and Ted for advice. Been a while as other life stuff took over. But now resolved,  would have helped if I remembered the difference between "fixed" and "floating" pad.
Still won't forget that error in a hurry. Or "Doh" as Honer would say. 🙄

Pages: [1] 2 3 ... 22