1
CB500/550 / Re: Top end o rings
« on: May 25, 2018, 12:10:14 PM »
Cheers Julie will drop you a list once I've deciphered cmsnl diagrams.
Try our re-instated info resource - "Aladdin's Cave" (Main menu)
- sorry it's taken so long to fix 
|
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
1
CB500/550 / Re: Top end o rings« on: May 25, 2018, 12:10:14 PM »
Cheers Julie will drop you a list once I've deciphered cmsnl diagrams.
2
CB500/550 / Top end o rings« on: May 25, 2018, 10:37:30 AM »
Hi guys
Anyone know where is best to purchase just the required O rings for a Top end rebuild of a cb550 without the gaskets. Cheers Gordon 3
CB750 / Re: Starting tips« on: May 25, 2018, 10:34:00 AM »
With mine I do the following: fuel on, choke on, kill switch set to off, throttle full open, hit starter/kick start till oil light goes out, flip kill switch to run and hit starter/kick start with half throttle.
4
Misc / Open / Re: Tax and MOT 400/4« on: May 20, 2018, 09:30:01 AM »
Same as above 1976 550f just taxed little declaration done.
6
CB500/550 / Re: 550 K3 spark plugs« on: February 09, 2018, 10:53:32 AM »
Don't know how correct this is and I think ES plugs where replaced with EA.
http://oldmanhonda.com/MC/DataTable.html 7
CB500/550 / Re: 550 K3 spark plugs« on: February 08, 2018, 03:09:51 PM »
Ngk D7ea should do the job as has no resistor.
8
CB500/550 / Re: Kickstart starting (or not)« on: May 24, 2017, 08:34:12 AM »
Mine can be a git when cold. Found this works for me: fuel on,ignition on kill switch in off position, hold throttle wide open, two/three kicks, kill switch to run, one kick and she lives.
9
CB500/550 / Re: Idle issues« on: May 16, 2017, 08:13:32 AM »
Honestly can't remember if it's third or fourth down. Think I'm third down but did drop to fourth at one point.
10
CB500/550 / Re: Idle issues« on: May 15, 2017, 10:52:30 PM »
Thats stock jetting I'm running 40 pilot and 110 main 1 1/2 out on the a/f screw. That's with 069a carbs, unipods and 4 into 1 header with a short reverse megaphone.
11
CB500/550 / Re: Cb 550 motogadget m unit« on: February 07, 2017, 12:43:45 PM »
M-unit uses ground signal to switch so what would be a 12v feed to the switches is grounded instead.
12
CB500/550 / Re: Cb 550 motogadget m unit« on: February 07, 2017, 10:37:39 AM »
From the manual you can set what controls you have on the bars.
7.7 Handle Bar Controls Three different types of handle bar controls are compatible with m-Unit. The particular type which will be used with m-unit must set in the setup menu. Configuration A) – 5-push button controls - turn lights left - push button - turn lights right - push button - low beam / high beam - push button - start - push button - horn - push button Configuration B) – Harley Davidson and BMW controls - turn lights left - push button - turn light right - push button - low beam / high beam - switch - start - push button - horn - push button Configuration C) – most Japanese and European motorcycles - turn lights left / right - 3 way switch - low beam / high beam - switch - start - push button - horn - push button configuration D) – new Ducati models - turn lights left / right - 3 way switch - low beam / high beam - push button - start - push button - horn - push button configuration E) – 4-push-button controls - turn lights left - push button - turn lights right - push button - low beam / high beam - push button - horn - push button - start = left turn + light simultaneously - kill switch = right turn + light simultaneously In case of using the OEM handle bar controls together with m-Unit; head light flashing push button is not applicable. There is also no possibility to switch the parking light by the m-Unit. Additional safety switches like side stand switch have to be connected as shown in chapter 7.9. 13
CB500/550 / Re: Cb 550 motogadget m unit« on: February 06, 2017, 02:13:00 PM »
You can use stock switches but have to select that setting in the m-unit menu. Also you have to wire them to switch ground not 12v.
14
CB500/550 / Re: Dynatek leads and stock plug caps« on: December 20, 2016, 06:07:16 PM »
Cheers guys just wanted to check as have a set of caps if need. Will run the dyna caps and see.
15
CB500/550 / Dynatek leads and stock plug caps« on: December 20, 2016, 03:45:26 PM »
Hi guys dumb question time. Fitting 5 ohm dynatek coils and dynatek leads which have plug caps pre formed, any need to cut pre formed caps off and fit ngk 5 ohm caps?
Cheers gordon
Pages: [1] 2
|