This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Corascate
1
« on: February 16, 2022, 07:19:07 PM »
Son
Dad I’ve got a part in the school play
I play a man who’s been married for 25 years
Dad
Maybe next time you’ll get a speaking part .
2
« on: December 08, 2020, 09:24:08 PM »
3
« on: November 18, 2020, 10:19:16 PM »
Apparently men have sex 2-3 times a week excluding eskimos who average 2 times a year.
This came as a distressing shock to me as I didn’t even know I was an eskimo
4
« on: August 31, 2020, 11:33:03 AM »
Some of the bikes were good fun back then, but the hairstyles and clothes sense was !!!!!!!!!
I still cringe looking at old photos, and wonder where my hair went.
5
« on: May 14, 2020, 11:47:09 PM »
Thanks for the info trigger and spr. I am slowly getting to realise that there are loads of variations.
S
6
« on: May 14, 2020, 09:46:59 AM »
Can anybody tell me if the air box on a k7 is the same as previous models, as my project bike has 4 separate cone type air filters and I want to put an original type airbox back onto the bike
Thanks
7
« on: May 08, 2020, 08:23:03 PM »
Hi all
I am going to weld the brackets back on the frame so that I can use it as it should be used.
My problem is that the Haynes manual gives measurements of 361mm (front mount to stand mount and 124 from a bolt above it on frame to stand mount )but. When I use a tape measure I can’t get both measurements to coincide .
Can anybody tell me what the measurements should be. Or even better could they make a template that could be emailed / posted to me and I could then get them in the correct place.
It wasn’t me who cut them off.
God knows why the previous owners cut them off but it wasn’t me.
I have looked through Bryanj (the oracle)microfiches and could not find anything.
The pics show one bracket held in position by cabletie and the other ready for when I have the correct measuement
Any advice is welcome
Thanks
Steve
8
« on: April 30, 2020, 11:00:26 AM »
Can anybody give me advise on whether it is feasible to change the pd carbs on my 77 K7 for some that are more “user friendly “ carbs
9
« on: April 26, 2020, 09:57:00 AM »
Quite apt
10
« on: April 25, 2020, 03:20:55 PM »
Hi Bryan
Like I said computers are weird things to me, I have been in my profile and I taplayout and it asks about hiding others avatars etc but I can’t find anything about putting my own on.
So I am obviously doing something wrong or maybe even on the wrong page.
What should I be looking for?
Steve
11
« on: April 25, 2020, 01:10:33 PM »
Hello all
How do I put an avatar on my profile
And also a signature ( I assume this is the catch line ! For example nurse Julie’s “trust me I’m a nurse†one)
S
12
« on: April 25, 2020, 10:51:12 AM »
Thanks for that bruxby Clive it’s perfect, I thought there had to be someone out there , but these are exactly what I want. Thanks again
13
« on: April 25, 2020, 08:36:54 AM »
im gonna have to find a new connector block and wire them in properly. there must be a suitable item available somewhere ,, hopefully one where you cann assemble the wires to the terminals and then push the terminals into the connector block. i have seen smaller versions on some boilers when wiring them in.
14
« on: April 24, 2020, 08:01:27 PM »
Another thing on these brackets, there is what looks like a buzzer connected with two wires coming from it on the near side bracket
15
« on: April 24, 2020, 07:55:26 PM »
Here’s the other side of the white connector block
|
Show Posts
