Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - roverboy

Pages: [1] 2
1
CB750 / viton tip float valve
« on: October 12, 2026, 04:42:14 AM »
hi can anyone help please as i am trying to buy viton tip float valves for my honda cb 750 k2 there seem to be available for other models

but not mine                                             
      so are they interchangeable any help would be appreciated regards john

2
CB750 / honda parts
« on: July 21, 2025, 04:50:58 PM »
hi all i need some parts that i cant get from david silver spares are cmsnl a good company to order honda parts from appreciate your opinion thanks

3
CB750 / Re: bearing shells
« on: February 01, 2025, 02:02:15 PM »
yes your right over here all the different plastigauge are  red but of course different  thickness truss us to be awkward regards john

4
CB750 / Re: bearing shells
« on: February 01, 2025, 01:33:55 PM »
hi archmill yes thanks for sending that I think that I was sent the wrong plastic gauge as all are red? any way checked with the right size and all good sitting on just over 1and1/2thou so now can get on with the rest of the rebuild many thanks for your input  regards John

5
CB750 / Re: bearing shells
« on: January 27, 2025, 05:34:19 PM »
hi the gauge is in  thousands of a inch

6
CB750 / bearing shells
« on: January 27, 2025, 02:27:41 PM »
my bearings shells

7
CB750 / bearing shells
« on: January 27, 2025, 02:21:15 PM »
hi all at sohc would appreciate your help with my bearings shells please refer to the pics checked with green plastic gauge on con rods and found this result an ovel shape not uninformed any help would be appreciated as not too sure what to think kind regards John 

8
CB750 / Re: brearing shells
« on: December 26, 2024, 01:17:13 PM »
Hi John.
Using all green shells in theory sounds great but that will only work if there is no wear on the crank shaft. You need to measure the current clearance with Plastiguage to see if they are all within spec still. Yes, you can use the existing crank bolts and Hondabond or similar is fine for the crank case halves and should be used very, very sparingly.
Out of interest, why do you think you need to change all the shells? Are they really pitted or scored?

9
CB750 / Re: brearing shells
« on: December 25, 2024, 09:56:03 AM »
hi all thanks for all your replies much appreciated not sure how i reply to each of you individually not good on computers  regards john

10
CB750 / brearing shells
« on: December 24, 2024, 01:07:32 PM »
hi all at sohc hope you can help me regarding replaceing my crank and con rod bearing shells am i right in thinking as all the original shells have green coding that  its ok to order like for like also should i reuse the old crank bolts or are they torque to stretch type and also i normally use three bonds1215 sealer but would honda bond be better would appreciate your comments and tips kind regards john

11
CB750 / Re: paint on engine block
« on: October 30, 2024, 05:43:03 PM »
thanks for your pics very helpful kind regards john

12
CB750 / paint on engine block
« on: October 30, 2024, 12:51:53 PM »
hi can any body tell me  should the engine block and head be painted or not as i am trying to keep my cb 750 original as i restore it any help would be appreciated

13
CB750 / Re: bore to piston clearance k2 advise please
« on: October 30, 2024, 11:43:52 AM »
many thank for you help by the way the rover name is my other love rover 90 p4 kind regards

14
CB750 / Re: bore to piston clearance k2 advise please
« on: October 30, 2024, 07:53:20 AM »
hi roverboy here thanks for all you replies will have to study the information from you all thanks again ps were the engine when new painted or untreated as would like to keep the bike original again thanks for your help 

15
CB750 / Re: bore to piston clearance k2 advise please
« on: October 29, 2024, 06:45:29 PM »
hi thanks to all your replies the reason i,m asking is that i had a rebore and the piston to bore clearance is set to 0,0004 1th and i am worried it will be to tight as the book says 0,0004 to 0.00016 would like your comments please

Pages: [1] 2