Stripdown Day 1 ..... the good the bad and the ...ugly.
The good first.
Lets be positive. So far there has not been a single stripped thread, sheared bolt or rounded off fastener. The back end is torn down and the rear wheel is out. Tank is off and the wiring all disconnected. The front end is all loosened up, and I just need to block up the front of the engine and drop the front end out. All the pinch bolts bar 1 are loose and everything is set for the last few jobs before I can pull the motor and sort the odds and ends. The bike is not sparkling as it should...so I need to work that out, but I will be doing it without the engine, just earthing the plugs direct to the frame so I can start on the engine once I clear some space in the shed.
The bad.
There was always going to be some, lets face it. It's a 40 year old bike thats been off the road for some time. There has to be a reason...and that's all part of the process. So...what did we find that we did not like today.
1) The exhaust has been off recently. All the nuts were loose, and 2 are missing. As are 3 of the 8 collets. The outside pipes had the 2 they should have. The inner ones had none. That's 4...but I said I had 5...yes. I found one in the little tray next to the battery box under the seat along with the battery strap. Hmmm... my guess....this bike had a good exhaust. Which was sold. A crappy rusted out pipe was then thrown on to sell it with the nuts done up finger tight so the headers felt attached.
2) The speedo drive was not connected at the bottom, and the screw is missing that locates it. The speedo is also quite battered when you look closely with the trip knob bent. The bezel is OK, but the chrome surround is grazed and out of shape. Worst of all...the speedo is blue faced. The tacho is green faced. One of them is not original. Any clues which is which? Can't believe I never spotted that one! Rookie error. No way I believe the stated mileage now. Not that I did anyway, in all honesty, but it was nicce to dream for a while
3) I got an oil leak. Left hand engine case. Left it on the side stand, and it was damp underneath
4) The headlamp is not original. In fact, it looks like it was never actually fitted! The wires and plug were not conected and clearly never had been. None of the clips holding the reflector into the housing were in palce either. All there....just not clipping anything. Judging by the corrosion staining..this was done a while ago, but someone has stuck a headlamp on so it had a headlamp....but never bothered to wire it in or mount it properly. Oh well...
5) Some one has tried to take the ignition switch apart, and the back is held on with a cable tie. Hmmm..oh yes...and the plug fell apart in my hand as I unplugged it. Ho hum. That's life!
The ugly.....
1) Julie was right about the rubber. Tank mounts, rear master cylinder rubbers, fork dust covers and all the little rubber mounts for electrical bits are all rock hard, crusty, or crumbling apart. But I expected it thanks to the advice on here. Still not pretty.
2) Fork seals are perished and oiling up the front, but no surprise there.
3) The seat is horrid, and the base is rusty too. Bin job I think. Not even worth putting on EBay. Sadly, the rear plastic cowl has some damage which will need repairing.
4) The wiring was a shocker. Some very odd bits of 'bridge work'. I started off carefully labelling each connector, but I soon realised this reference work may be wasted as I want to reconnect everything the way the book says....and this sure as hell isn't that!
So, tomorrow..the strip continues, and I can see how straight the frame and front end are. Plus remove the horrid forward pegs someone has added. Still gobsmacked that all the bolts have come undone with no more than WD40 and a ratchet. No breaker bars, lump hammers or swearing. Closest I came to that was the rear wheel spindle. It had corroded on the sprocket side and needed a soak before it shifted. The chain adjuster block that side was grotty too...but the other side is perfect. It should clean up OK.
Here's a bucket load of pics....
Some bits here to keep...and the tail pipe to scrap
All the backend, the little toolbox and the worlds ugliest seat. It has a row of rivets for the buttons....bleurgh. I will remove teh plastic cowl, the catch and hinge. The last two will go on whatever seat I do use in the end.
Why do I have an exhaust collet under the seat......
Swingarm out, and it's grubby in here....but not rusty. Chain is shot...but both sprockets could actually be used....I won't but...well...Worst rust is on the centre stand lower half. It's all solid though and should clean up nicely.
Not so clean under the tank, with a bit of frame rust...but again, nothing deep or serious. Coils have been messed with. One has 'CB750' in marker pen on the side. Replacement from a breakers. Both are marked 'TEK'. The corroded terminals and general state of the wiring probably has a lot to do with the spark issues.
Those are genuine FVQ shocks. They probably stil do fade very quickly....but they don't leak. They have bugger all damping, so probably don't leak due to having no oil.....
Who did this....why did they do it....can I have them shot please.
It's shiny...it's never been properly fitted. I might actually use it. The rubber boot over the bulb hole is also perished.
So here's where we stopped. A mixed bag of stuff, but impressed with the build quality. Nervous about what I will find lurking in the engine, but also prepared for that to swallow the bulk of the budget. If I get off lightly there...that leaves more for nice pipes and professional paint. I also got a real reminder of how things have changed when I picked up the rear wheel and nearly ruptured a disc. Do they use air or lead to fill the tyres?