Other Stuff > Interchangeability

Rear Lamp needed sought with mounting holes 100mm wide at centre line?

<< < (2/8) > >>

gary123:
Ted, do you need the whole lamp, ie chrome and lens. I have spare lens in great nick but the chrome has been painter over.
If you think it will do I can put some pics up in the am.

McCabe-Thiele (Ted):
DS replica is only £17.94 plus VAT at the moment looking at a LED complete unit as an alternative.
It will need a little creative cutting but this was cheap enough to have a go with.

.https://www.ebay.co.uk/itm/354419352010?_trkparms=amclksrc%3DITM%26aid%3D1110013%26algo%3DHOMESPLICE.SIMRXI%26ao%3D1%26asc%3D20211130130958%26meid%3D47f5b54c8cdb4e5f8cbb3cbb9167de03%26pid%3D101469%26rk%3D4%26rkt%3D4%26sd%3D224846567524%26itm%3D354419352010%26pmt%3D1%26noa%3D0%26pg%3D3650466%26algv%3DSimplAMLv5PairwiseWebNoToraCoCoViewsNoHighIdfOrSortByFinalScoreBlenderWithPromotedViewItems%26brand%3DUnbranded&_trksid=p3650466.c101469.m2822&amdata=cksum%3A35441935201047f5b54c8cdb4e5f8cbb3cbb9167de03%7Cenc%3AAQAHAAABQGdVN27N8r3oD%252Ba0m6XTQ8CHCNvMcr5tWVySNo6oEVToAx28k8doednsS4bNzFXwbeFCXGUtW08AVoz58bdB2RfrwyaNw8WFNSxsQz%252FX%252FLat%252BO5uB80x3DKRQbrLp6YIazdjxpMZHrjf5CVmAMBCJitMTt9LfA3UfLZCXSH4VzNh4Yvu6asaJCLesZGyiixty9WX45o3mM%252BO8dxF7038Tr3%252FTpzlo4nhceqPZOxOZbRwuR3uYJdVs21vBB01T2%252FXg2uHIsQ7glM2elNNHVRiBWpnKgz08qNAqJGz3UYGPqBANzs4xdy%252FDSuZMHIgJsKFfTfhHjqMNdohIEtUBLx2LpxNZlIPeQOnpmbdrP7n%252BqGuyi%252BQ4HW4aYU7LbsHp3hyn31xKVSNeVJFXLlDiFsWoEXFLoMJKHZGdJOcYdtnjtEl%7Campid%3APL_CLK%7Cclp%3A3650466&epid=3021855018

McCabe-Thiele (Ted):
Okay I need to sort out the "sandwich" a tad better as the side view is not acceptable - but the lamp will fit!

In an ideal world a nice block of aluminium would sort out the gap between the LED lamp & the rear number plate mounting.  Aside from the cost it's a lot of cutting that would be far from perfect.

Looking for ideas such as a plastic infill block that's easier to cut. Any ideas welcome to fill the gap properly.

rear LED lamp by Macabe Thiele, on Flickr

.mind the gap by Macabe Thiele, on Flickr

Sesman:
I nicely shaped hardwood spacer?

Seabeowner:
Or get someone to 3D print something.

Navigation

[0] Message Index

[#] Next page

[*] Previous page