« previous next »
Pages: 1 2 3 [4]   Go Down

Author Topic: 500 engine strip  (Read 9958 times)

Offline kenny1059

  • SOHC Associate
  • Posts: 66
    • View Profile
Re: 500 engine strip
« Reply #45 on: June 23, 2014, 11:43:25 AM »
Done!! :)
If anything, I was compressing spring to much. But doesn't matter now,as they are in and seated with the help of a rubber mallet. :) :)

  Kenny.
Logged
CB 400F (1976), Yamaha XJ900 Diversion (now deceased), CBF 600 (2011). VFR 800 Crossrunner (2015).

Offline Trigger

  • Grogu
  • *
  • Posts: 8436
  • Engines built on reputation, not advertising.
    • View Profile
Re: 500 engine strip
« Reply #46 on: June 23, 2014, 04:37:40 PM »
Well done Kenny. See if you try it all happens in the end.
Logged

Offline Trigger

  • Grogu
  • *
  • Posts: 8436
  • Engines built on reputation, not advertising.
    • View Profile
Re: 500 engine strip
« Reply #47 on: June 23, 2014, 05:39:29 PM »
Before putting the head back on check that all the valves are seated. By testing them with fuel down the ports. Do not know if you have re-cut the seats and lapped the valves in???
Logged

Offline kenny1059

  • SOHC Associate
  • Posts: 66
    • View Profile
Re: 500 engine strip
« Reply #48 on: June 23, 2014, 06:48:12 PM »
Nice one Oddjob.  :) :) :) :) :) :)
Lapped valves etc. yesterday. All is o.k.  :) :)

  Kenny.
Logged
CB 400F (1976), Yamaha XJ900 Diversion (now deceased), CBF 600 (2011). VFR 800 Crossrunner (2015).

Offline mickwinf

  • SOHC Master
  • Posts: 1750
    • View Profile
Re: 500 engine strip
« Reply #49 on: July 07, 2014, 09:09:16 AM »
More progress, got the valves installed with my new spring compressor (ebay £20) fitted the head with genuine Honda gasket. Just the rocker top to install then engine is complete ready for carbs and exhaust. Cant wait for the first start up!
Logged
Love the 500 and 550 have a 500 called Lazarus under restoration

Offline mickwinf

  • SOHC Master
  • Posts: 1750
    • View Profile
Re: 500 engine strip
« Reply #50 on: July 23, 2014, 10:33:07 PM »
exhaust and carbs fitted, a bit of electrics to do before first start up. Problem is I have been on ebay again and bought a 550!!
 http://http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=181470532096
Logged
Love the 500 and 550 have a 500 called Lazarus under restoration

Offline mickwinf

  • SOHC Master
  • Posts: 1750
    • View Profile
Re: 500 engine strip
« Reply #51 on: August 10, 2014, 09:02:18 PM »
It lives!!!! yes got it going today, sounds good but valves will need doing again and carb sync, bottom end sounds quiet with hardly any clutch rattle or chain noise. Good day!
Logged
Love the 500 and 550 have a 500 called Lazarus under restoration
Pages: 1 2 3 [4]   Go Up
« previous next »
 
SimplePortal 2.3.5 © 2008-2012, SimplePortal