This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - yozzer74
31
« on: September 24, 2016, 04:41:22 PM »
Well I've fitted new seals in my calipers pistons were in good order just been in garage and all 3 are leaking why .I bought these calipers from eBay .
32
« on: September 11, 2016, 07:17:17 PM »
Hi just gone to fit my front sprocket but I've forgot which way it goes .I'm sure I've seen a thread on this before but I can't find it .also what length 8mm bolt hold it on and washer .can't seam to find them .and can't see them on parts finch .thanks in advance yozzer
33
« on: August 22, 2016, 09:02:45 PM »
Hi I've been helping a mate with is f2 engine .it was tapping really bad when we removed tappit covers there was no oil on right hand side . So engine out and stripped .found oil jet on that side blocked the can now has a little lip on it now picture below .is it toast now can it be repaired and is the f2 can different to other models .has anyone got one spare .cheers yozzer [ Guests cannot view attachments ]
34
« on: July 29, 2016, 03:31:53 PM »
Hi I've bought this Gs550 to do something with .bit undecided has yet what to do with it yet .quick question does anyone recognize what the silencers are off the PO told me they were off a British bike ?? [ Guests cannot view attachments ]
35
« on: July 26, 2016, 06:08:15 PM »
Hi could anyone help just been looking how the front break spliter fits on bottom yoke mine as a dodge home made bracket on it it may not even be the correct spliter .it's for the f2 78 does anyone have any pictures of there's .thanks yozzer.is it possible not to use one at all
36
« on: July 12, 2016, 08:52:04 AM »
Hi as anyone got any recommendations for reg/rectifier unit .I've seen all different prices for them. how do you no what your buying is any good .
37
« on: July 03, 2016, 09:14:02 PM »
Tested bike for charging I'm getting way too high volts meter is showing 19 volts when I rev bike a little .could I have wired reg rec up wrong to cause this. or is the reg rectifier just broke
38
« on: June 28, 2016, 09:06:14 PM »
Had bike running today just in garage oil pressure was 60 then on tick over 20 but after 5 mins dropped down to 0 .but when reved goes back into 20 .is it because it got too hot .
39
« on: June 14, 2016, 08:41:47 PM »
Don't no best place to put this .so I have put it here . help measure the pitch size
If you measure 10mm of thread and count the threads. If you count 8 then it is 1.25 (8 x 1.25 =10)
If you measure 9mm and count 6 then it is 1.5
If you measure 10mm and count 10 then it is 1.0 .
40
« on: June 09, 2016, 04:30:26 PM »
Hi how do you get oil pressure before starting bike for first time after rebuild..
41
« on: June 01, 2016, 10:29:50 PM »
Hi I'm thinking of buying these coils does anyone no if they will work with a points ignition on a cb750 f2 .Cheers
42
« on: May 20, 2016, 07:59:37 PM »
I'm on with making my wiring harness .I've wired indicators up with new led relay but they won't flash .they just stay on solid.any ideas
43
« on: May 14, 2016, 08:20:01 PM »
Hi I'm wanting to extend my starter motor cable does anyone no what gauge size I will need cheers yozzer
44
« on: March 02, 2016, 09:27:46 PM »
Hi does anyone know best place to buy wire & connectors for making wiring harness.cheers
45
« on: January 26, 2016, 10:02:50 AM »
Hi I'm going to try to make my own wiring harness .does anyone have any diagrams of custom harnesses .looked on line but can't seem to find any .the less wires I can get away with the better .
|
Show Posts