This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Sprocket
Pages: 1 ... 3 4 [5] 6 7 ... 10
61
« on: June 03, 2019, 08:15:08 AM »
Whatever you do, don't email Cruzinimage asking for rings. I did just that about 12 months ago. I didn't get a reply and they blacklisted me on eBay, people asking questions are troublemakers. So now if I want to buy off them I have to order direct from their own website. Not completely bad as their website is cheaper than eBay. They are a really strange bunch of people. And while were at it, don't buy anything off them that has rubber components or gaskets, they are total shite.
You won't believe this then, I asked a question on the ebay listing 'can I buy a ring, I've broken one' and they emailed me straight back. Total cost is £17, which waters my eyes a bit, but at least it'll be from the same supplier so I know what I'm getting.  Cheers all!
62
« on: June 03, 2019, 08:12:05 AM »
Unfortunately can't help you with the piston ring. I'm still trying to work out what you were doing with the feeler gauge near the piston ring once fitted 🤔🤔🤔
They weren't 'fitted' at that point. Being very worried about splitting a ring, I was being really careful and used two to cover each of the ends of the ring as it went over the top gap, so it couldn't drop in where I didn't want it. (bit like this:  Then it slipped...
63
« on: June 02, 2019, 03:21:54 PM »
Any chance someone has a single (new) black piston ring i could buy? I have a cruzinimage standard size piston set, all went together ok but i ham-fistedly broke a black one when my feeler gauge slipped. 
64
« on: May 26, 2019, 02:50:22 PM »
So next question then; is David Silver the only supplier? My Japanese isn't good, so i fear the answer is yes.
65
« on: May 25, 2019, 10:07:27 AM »
Haha i should leave a space between pics in future!
66
« on: May 24, 2019, 08:56:30 PM »
I think the camera flash had a lot to do with it. I was highly unsure about the number on its own until i looked at the pics.
67
« on: May 24, 2019, 04:30:23 PM »
Hello. Quick sanity check if I may (Oddjob, Julie, etc...)
I have a case with BBBAB on it, and my crank looks like this:
[ Guests cannot view attachments ] [ Guests cannot view attachments ]
I think I need 4 sets of green and one set of brown mains and four sets of green big end bearings.
B1, B1, B1, A2, B2
2B, 3A, 3A, 3A
That seem right?
68
« on: May 10, 2019, 08:36:59 AM »
I was considering this the other day actually. I have a crank with one still attached, I will be taking it to my local hardware supplier tomorrow to ask them to try a bunch of screws in, when I get the right one I'll let you know.
You just grease it up and wind it in, right, same as a bicycle crank extraction?
69
« on: April 26, 2019, 01:45:02 PM »
I'm pretty sure the camera is showing it up a bit. I don't have a printer, but a guy in another one of our offices does. I can't tell you what the printer is or what filament it's using - but I'm pretty happy with it so far! I might need a couple more done, so I'll investigate what the resolution is at that point.
70
« on: April 26, 2019, 09:11:07 AM »
I have a button! Very pleased with this, thank you so much!
[ Guests cannot view attachments ]
I will need to excavate the back of it to take the metal slot, but that's pretty straightforward with a small drill bit.
I imagine loads of people will be after this STL file now...
71
« on: April 24, 2019, 03:02:18 PM »
M6 carriage bolts?
72
« on: April 20, 2019, 09:13:13 AM »
Awesome, thank you very much! Will pm you 
73
« on: April 16, 2019, 06:50:47 PM »
That's the little bit yes! If you could take as many pics as possible, perhaps put it on a flatbed scanner, I'm sure that would be a good way to start! Thank you!
74
« on: April 16, 2019, 04:55:59 PM »
I have nothing except a stump of metal with a hole that comes out of the switchgear. I'd love someone to help though!
75
« on: April 13, 2019, 09:34:12 PM »
Has anyone come across any useful 3d printer files at all? I'm specifically thinking of the horn button on the 400, but I've run out of Google-fu trying.
Pages: 1 ... 3 4 [5] 6 7 ... 10
|
Show Posts