This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - mickharrow
1
« on: October 16, 2015, 09:18:11 PM »
I have a set of exhaust flanges with new countersunk screws and copper washers for sale. looking for £35 and I will post to the uk in this price. Cash or cheque whatever suits.
2
« on: October 06, 2015, 10:12:35 AM »
for the last 3 years i have been building a cb750 special to use for sprinting over the 1/4 mile and abiout 3 months ago got it finished and running.i have now been told that the acu will no longer allow me a race license due to my poor health so i am buggered.if anyone is looking for a project this would still make a good track bike or a road legal cafe racer but is not for the purist who wants everything genuine as per original.the frame has been strenghtened and had the top frame removal conversion,the engine has had a total rebuild including wisco pistons and is now 840cc complete frame wheels etc powder coated black,rask rearsets plus loads of spares.
if this is of interest to anyone then please feel free to have a look otherwise i will convert to cafe racer next year and enjoy on the roads just feeling a bit down at the moment to have my sporting career which has been ongoing for many years stopped in this way.
3
« on: August 03, 2015, 11:58:49 AM »
This might sound like a silly question but does the lower crankcase breather vent to atmosphere or does it vent back through the oil tank
4
« on: July 03, 2015, 03:01:16 PM »
Had serious clutch drag so pulled the clutch out today and checked everything and looked ok.
Still dragging badly and the arm that the cable goes into is moving but not a great deal and I have adjusted the centre screw and nut as recommended.the clutch is years old as I am putting together what was a basket case so wonder if a new clutch and springs are in order,opions please
5
« on: June 22, 2015, 10:24:05 AM »
having completed my cb ready for the track i have some bits left over which may be of use to someone,they are as follows
pair of wheels,set of carbs,top and bottom steering stem,swinging arm plus a box of bits and pieces.
dont want much for them or will swop for anything usefull
collection from ringwood
6
« on: April 15, 2015, 05:22:17 PM »
Has anyone got a rotor set bolt that holds the rotor onto the shaft for sale,need one urgently
7
« on: March 17, 2015, 12:10:18 PM »
Has anyone got a pair of split collars that go into the head and are held by the finned collar to enable me to finish my project?
If you have and wish to sell them just advise price with postage and I will happily pay
8
« on: March 03, 2015, 12:49:45 PM »
Can anyone tell me the size for the bolts that hold the cover over the ignition on the near side
Thank you
9
« on: October 29, 2014, 10:33:24 AM »
Has anyone got a rear wheel spacer left hand side they could sell me. This is the straight spacer not the stepped one.none available from usual sources
Thank you
10
« on: July 11, 2014, 03:37:39 PM »
Anyone got a set of Cush drive rubbers for a f1 cb750. they want to sell
Thanks
11
« on: December 26, 2013, 07:51:50 PM »
I am looking for a set of 4 springs for a set of carbs for my early 750
The carbs are the type that connect to a rod the runs the whole length of the Carbs and a single cable pulls all four carbs open together
Can anyone advise where I can purchase or if anyone has a set to sell the I will gladly purchase
Have tried David silver and a couple of keihin suppliers with no luck
12
« on: December 05, 2013, 04:16:34 PM »
I am working on a basket case and have four carbs in bits which I trying to rebuild with some difficulty
An anyone suggest a company who can supply parts or better still do the rebuild
I am aware of David silver but trying another avenue first
Better stil anyone got a set of carbs all built up they want to sell
Regards mick
13
« on: November 11, 2013, 02:55:52 PM »
can anyone reccommend a good engine man in the south of uk [ i am in east dorset ] who can have a look at an engine i have
thanks
14
« on: October 16, 2012, 09:32:16 AM »
a while back there was a post about fuel tank cleaning but the link to the halfords product was not working.
amyone suggest a good project to clean inside a fuel tank that has stood empty for a long while?
15
« on: July 25, 2012, 03:49:38 PM »
just got a set of raask rear sets for my project bike but on the brake side all there is attached to the brake arm is a short rod with a swivel joint at each end
can anyone post any puictures to show how this all links in to the rear drum brake
any help would be much appreciated
mick
|
Show Posts