Recent Posts

Pages: 1 [2] 3 4 ... 10
11
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by Bryanj on Today at 07:28:22 PM »
That was a good haul, too much and too far away for me, at least 3 of the rear brake pedal retun spring in there
12
Project Board / Re: Doms CB550F1 project
« Last post by DomP on Today at 07:25:28 PM »
I got there in the end, it took ages to get air out of the new master cylinder which was made harder because my clip ons have a 15° downward angle on them so air was sitting at the top slightly above the mc piston inlet.  Solved it by rolling the bike up the slope of my drive and putting it on the side stand. 

Lesson learned!
13
The Black Bomber Board / Re: 67` Bomber running problems
« Last post by mo goldie on Today at 07:19:03 PM »
are thanks Ash........ well its Not just the mrs then that I upset LOL

so I have sent that off to the bloke .... I hope he will find a sprocket that will fit with them Dimensions.

so thanks Again Ash to the rescue  ;D or should I say MR Honda  ;D
14
Project Board / Re: The rebirth of Lazarus
« Last post by mickwinf on Today at 06:22:16 PM »
had a chance to try a ride, only about 10 miles but a big improvement on before. the big flat spot is much reduced since changing the needle clip position and the clutch also feels better. A weird thing happens though when i open the throttle to accelerate It sometimes snatches as if i had momentarily pulled the clutch in, strange, and carbs still need setting better as get a hanging idle sometimes. At least I had an enjoyable ride with a reasonable chance of getting home with no unplanned stops!
15
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by McCabe-Thiele (Ted) on Today at 06:00:55 PM »
No bids on the bike.

Parts sold a good haul for someone - anyone here?
16
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by McCabe-Thiele (Ted) on Today at 05:58:59 PM »
Plus a load of spares.

https://www.ebay.co.uk/itm/335384696747?itmmeta=01HY8WH3W9Q21HT7P0WPPTR7EK&hash=item4e167c57ab:g:NNcAAOSw7hJmO6PG
17
Desperately Seeking!! / Re: I'm after a 400/4 points plate...
« Last post by McCabe-Thiele (Ted) on Today at 05:51:59 PM »
Steve has  a few listed - his prices are sensible.

https://www.400fourbits.co.uk/#electrical
18
CB500/550 / Re: 500K0 unfinished project on eBay
« Last post by Nurse Julie on Today at 05:08:22 PM »
I know Chris lives up your way Ash, he's a very good customer of mine and has been buying parts from me regularly for quite a few years now.
19
CB500/550 / 500K0 unfinished project on eBay
« Last post by AshimotoK0 on Today at 04:05:39 PM »
I know this guy but haven't seen him for years
100% genuine bloke though

https://www.ebay.co.uk/itm/335388847413
20
Desperately Seeking!! / Re: I'm after a 400/4 points plate...
« Last post by Matt_Harrington on Today at 04:02:00 PM »
I just assumed that as the points plate was stamped 333, then it was specifically for the 400/4. Anyway, still after one.....  ::)
Pages: 1 [2] 3 4 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal