SOHC.co.uk Forums > CB350/400
On a genuine CB400/4 rear mudguard how many number plate mounting holes?
McCabe-Thiele (Ted):
--- Quote from: Nurse Julie on October 25, 2021, 01:23:21 PM ---
--- Quote from: Macabethiele (Ted) on October 25, 2021, 01:19:11 PM ---Nice rear fender you have there - what's with the chain guard - not chromed - is it a fully painted one ?
P.S. I've drilled out my mount and it fits a treat except I have no third collar insert - they seem to be unavailable.
--- End quote ---
Ted, Graham may have a spare insert, I'll ask him later.
--- End quote ---
Thanks NJ it would stop it crushing the rubber - I don't have any small tubing I can cut down - not even in plastic. Ted
Nurse Julie:
--- Quote from: Macabethiele (Ted) on October 25, 2021, 02:06:44 PM ---
--- Quote from: Nurse Julie on October 25, 2021, 01:23:21 PM ---
--- Quote from: Macabethiele (Ted) on October 25, 2021, 01:19:11 PM ---Nice rear fender you have there - what's with the chain guard - not chromed - is it a fully painted one ?
P.S. I've drilled out my mount and it fits a treat except I have no third collar insert - they seem to be unavailable.
--- End quote ---
Ted, Graham may have a spare insert, I'll ask him later.
--- End quote ---
Thanks NJ it would stop it crushing the rubber - I don't have any small tubing I can cut down - not even in plastic. Ted
--- End quote ---
Ted, could you measure the OD and depth please, would also help if I knew the part number.
wildtapholer:
--- Quote from: Macabethiele (Ted) on October 25, 2021, 02:06:44 PM ---
--- Quote from: Nurse Julie on October 25, 2021, 01:23:21 PM ---
--- Quote from: Macabethiele (Ted) on October 25, 2021, 01:19:11 PM ---Nice rear fender you have there - what's with the chain guard - not chromed - is it a fully painted one ?
P.S. I've drilled out my mount and it fits a treat except I have no third collar insert - they seem to be unavailable.
--- End quote ---
Ted, Graham may have a spare insert, I'll ask him later.
--- End quote ---
Thanks NJ it would stop it crushing the rubber - I don't have any small tubing I can cut down - not even in plastic. Ted
--- End quote ---
I bought a couple of bags of the grommets and spacers from china, cheap but cheerful, does the job and a I cut them down to length, that's what I used on my number plate carrier if you look closely.
wildtapholer:
--- Quote from: Macabethiele (Ted) on October 25, 2021, 01:19:11 PM ---Nice rear fender you have there - what's with the chain guard - not chromed - is it a fully painted one ?
P.S. I've drilled out my mount and it fits a treat except I have no third collar insert - they seem to be unavailable.
--- End quote ---
Had to paint it was too far gone, re-chroming is far too expensive and that's if you can find anyone who can be bothered to re-chrome it, had to buy a new tank filler cap for the same reason+ the old one needed a new seal as well, this paint works really well from screw fix
wildtapholer:
--- Quote from: Macabethiele (Ted) on October 25, 2021, 02:06:44 PM ---
--- Quote from: Nurse Julie on October 25, 2021, 01:23:21 PM ---
--- Quote from: Macabethiele (Ted) on October 25, 2021, 01:19:11 PM ---Nice rear fender you have there - what's with the chain guard - not chromed - is it a fully painted one ?
P.S. I've drilled out my mount and it fits a treat except I have no third collar insert - they seem to be unavailable.
--- End quote ---
Ted, Graham may have a spare insert, I'll ask him later.
--- End quote ---
Thanks NJ it would stop it crushing the rubber - I don't have any small tubing I can cut down - not even in plastic. Ted
I got these off ebay and cut the spacers down if they were too long.
--- End quote ---
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version