This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Nurse Julie
Pages: 1 ... 516 517 [518] 519 520 ... 527
7756
« on: January 02, 2015, 09:15:53 PM »
i thought the one at the bottom of the airfilter box was the only one that had the pinch slit at the bottom the one on the air chamber was just a hole ??
Hi Steven. Yes, that's what I'm saying. On my bike the one with just the hole in the bottom that should be coming off the inlet manifold has been put on the bottom of the air filter box by someone in the past in error, there is no pipe at all attached to the bottom of the manifold. So all I need to do is swap the one with the hole over to the inlet manifold and obtain a new one with a pinch drain for the air filter box. Regards Julie
7757
« on: January 02, 2015, 08:36:49 PM »
Hi Ken.
Thanks for that. It is the correct part No. but it seems to not have the pinch drain on it anymore, maybe it's one of those things you don't really need.Why have a pinch drain when you can just let is come out with gravity instead
Regards
Julie
7758
« on: January 02, 2015, 08:16:50 PM »
Just looked on DSS and the drain pipe from the air filter box with the pinch drain at the bottom is now an obsolete part. Does anyone know where else I can get this from?. Its Part No 17358-374-000. They still do the breather pipe from the bottom of the air inlet box which is handy as that's the one I'm missing completely.
Julie
7759
« on: January 02, 2015, 07:12:47 PM »
Hi Tom.
Ah ha, now I can see with the enlarged pic. Right, there is no pipe coming off the bottom of the inlet manifold, I can see where the pipe attaches and that would go straight down through the hole I was asking about. But.....no spare pipe in sight so I think that has fallen off in the past. Then the pipe coming off the air filter case would go down almost horizontal through the guide under the centre stand pinch bolt. That all makes a bit more sense now. I think I just need to buy a new pipe from the inlet manifold and a new pipe with the pinch drain for the bottom of the air filter case.
Thanks very much Tom, very helpful
Regards
\julie
7760
« on: January 02, 2015, 06:44:45 PM »
Hi Tom.
Thanks for looking and the pics. Yes, I do have all the original guides which is handy. It must have been the PO that stuffed the pipe from the airbox down there but the end was not attached to the airbox, it was only when I tried to attatch it to the plastic tube on the box that I realised it would kink. I will need to have a good look at it again tomorrow as I think the pipe is actually upside down, or even the wrong pipe as the pinch drain is at the top not the bottom !!!!.
Regards
Julie
7761
« on: January 02, 2015, 04:10:18 PM »
Hi Chaps
On the back of my engine, just above and below where the crankcase splits at the same level as where the swinging arm sits, there is a long horizontal hole, or tube in the engine casting. Either side are bolts joining the bottom of the engine to bit of the engine on top but between these bolts is this tube. At the moment the drain tube from the bottom of the air filter case is routed through this tube but not only does it not look right but the angle of the tube is so acute it crimps and occludes the tube. I have worked out that is not correct and have re routed it but what should be in that tube, if anything?. Sorry, tried to take a pic but so tight in there even with swinging arm out that nothing really showed.
Ta in advance
Julie
7762
« on: January 01, 2015, 05:53:18 PM »
Ooops, looked like brass to me 
7763
« on: January 01, 2015, 05:13:08 PM »
Should I get brass or alloy gaskets ? 
7764
« on: January 01, 2015, 04:16:46 PM »
Depending on the age of the gaskets when fitted, there's a very high chance that the fibres you're seeing are asbestos, so bw especially carefull getting them out as you know how harmful the dust can be:'(
You were right Hairy. Just happend to have some surgical masks at home so put 1 of them on and gaskets straight into a bag and tied, I don't think I will come to any harm with that small amount and they came out without breaking. Thanks for that. Julie
7765
« on: January 01, 2015, 03:01:29 PM »
With the gaskets still in situ I must say I can't see any copper at all, only what appears to be fibre. I will take them out later and have a closer look but have decided to fit new ones anyway
Regards
Julie
7766
« on: January 01, 2015, 02:55:41 PM »
7767
« on: January 01, 2015, 02:50:20 PM »
7768
« on: December 31, 2014, 08:25:26 PM »
7769
« on: December 31, 2014, 08:13:58 PM »
Happy New Year everyone, lets hope it's a safe and happy one. Thanks for all your advice and the banter, it really is a fun forum. Wish me luck, off to work now in A and E and it's not going to be nice  . Julie x x
7770
« on: December 31, 2014, 06:58:58 PM »
Yamiya are selling a pair for 10000 yen. Not sure what the equates to in Sterling though.
Thats still about £54, better but still pricey 
Pages: 1 ... 516 517 [518] 519 520 ... 527
|
Show Posts
