SOHC.co.uk Forums > Project Board

Honda CB400NA Superdream - new money puddle.

<< < (4/60) > >>

Laverda Dave:

--- Quote from: McCabe-Thiele (Ted) on October 13, 2024, 02:43:30 PM ---Just back from Stafford Show, it was dry but there were lots of empty stalls inside with a lower attendance it seemed. We did not find a Honda stand or see a 400N with just one 250 Superdream.

Ran the engine when I got back, the oil looks as though it's leaking mainly  from the very  top  cover, oil then runs along the top fins on the cylinder head down the valley between the two cylinders. It made me wonder if the vent pipe is trapped.

I can see that the invoices included fitting two Time Serts as they do not use long studs but very long head bolts that reach through the head & block screwing into the upper engine case.

--- End quote ---

From your diagnoses Ted I think someone has taken the 400 engine out and substituted it with a 350 Triumph engine, my Triton has exactly the same symptoms. The advantage is your boots will be totally waterproof  ;)

McCabe-Thiele (Ted):

--- Quote from: Laverda Dave on October 14, 2024, 01:55:18 PM ---
--- Quote from: McCabe-Thiele (Ted) on October 13, 2024, 02:43:30 PM ---Just back from Stafford Show, it was dry but there were lots of empty stalls inside with a lower attendance it seemed. We did not find a Honda stand or see a 400N with just one 250 Superdream.

Ran the engine when I got back, the oil looks as though it's leaking mainly  from the very  top  cover, oil then runs along the top fins on the cylinder head down the valley between the two cylinders. It made me wonder if the vent pipe is trapped.

I can see that the invoices included fitting two Time Serts as they do not use long studs but very long head bolts that reach through the head & block screwing into the upper engine case.

--- End quote ---

From your diagnoses Ted I think someone has taken the 400 engine out and substituted it with a 350 Triumph engine, my Triton has exactly the same symptoms. The advantage is your boots will be totally waterproof  ;)
[/quote

To be fair to my old Triumph 21 it only leaked oil when stood overnight - it did not pump out when the engine running.
--- End quote ---

Laverda Dave:
I've just come in from the garage Ted. I took the rocker covers  off the Triton engine today attempting to cure the oil weep. I've fitted copper gaskets with wellseal! The trouble with old British bike engines is they were made using worn out tooling and the world and his brother have all had a go at them on the cheap😏.
Give me a Japanese engine (or an Italian one) anyday!

I'm going to get back on finishing Ratty in the next few days, I had to take a break from it after all the aggravation of the carbs. I'm refreshed enough to strip them......again!

Laverda Dave:

--- Quote from: McCabe-Thiele (Ted) on October 13, 2024, 11:46:22 PM ---The genuine seal at DS is £19.70, aftermarket part £9.00 is the cheaper option as good?

The top seal/washers are £7.70 each, so it's a total of £35.10 or £24.40 - just to cheer me up there might be a second leak lower down!

--- End quote ---

For the sake of an extra £10 I would always go for the genuine part (assuming the DSS part is genuine Honda and in a Honda bag). Imagine fitting a pattern part and it still leaks, you wouldn't know if it was the pattern part or another issue. If a genuine part is still available I would always use it just for peace of mind that you know it's correct and it will fit properly.

K2-K6:
An interesting project Ted, looking forward to seeing it progress.

Isn't the rocker cover fitted and secured by two sleeve bolts on these with rubber seals  ?  Much like a A series BMC type but with that T fitment instead of traditional cork  ;D

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version